PSoC 4 MCU

(1) I set the beak segment detection length to 11, but when sending a beak segment with a length of 11.3 bits, the break detection interrupt cannot be triggered.

(2) In the face of such a situation, is there any way to detect the 11.3 bit break segment? What kind of hardware changes or software processing needs to be done.

Hi,

I'm using AN86233_DeepSleepADC.cydsn project, but the current is about 1.8mA insted of 9uA as read in comments of project. Someone can explain me the reason?

Tanks in advance! 

Hi, 

I am referring to the below examples to test BLE Bonding between two pioneer kits.

https://github.com/Infineon/PSoC-4-BLE/blob/master/100_Projects_in_100_Days/Day015_Bonding/BLE_Bonding.pdf

https://github.com/Infineon/PSoC-4-BLE/blob/master/100_Projects_in_100_Days/Day011_Central_Observer/BLE_Central_Observer.pdf

Individually the examples work fine. But my requirement is: One pioneer kit should act as a BLE central and will connect to another pioneer kit that is acting as BLE peripheral. BLE peripheral is having below security requirements.

Connection with the peripheral using the Cysmart app works as expected. But how can I tweak the code on central to work with a peripheral with the above GAP settings?  Is there an example available for it?

I also have a requirement where I want to restrict the peripheral to be pared/bonded with just one central at a time.

Regards

Hi,

If I export the data acquired by Bridge Control Panel to a file in excel format, only the latest 10,000 data can be saved.

Is it possible to increase the number of data that can be saved as a log?

Bridge Control Panel  V1.22

Best Regards,

Naoaki Morimoto

PSoC 4100SシリーズのCapsenseについて、型番によってジェスチャが使えるものと使えないものがあります。

configureとしてはジェスチャは未使用(Enableしない)とするとして、

ジェスチャを使う事が出来る型番(ex.CY8C4146-S433)でのCapsenseと

ジェスチャを使う事が出来ない型番(ex.CY8C4126-S433)でのCapsenseで比較したとき、

ボタンなどで使用した際に、感度などの違いは出るでしょうか？

個体バラツキは出るかと思いますが、仕組みとして違いが出るようであれば知りたいです。

I am working on 2x3 Cap Sense matrix keypad interfacing using PSOC4 ,

but i am facing difficulty in software section. Can anyone give suggestion on it.

Dear Sirs and Madams,

We understand that the CapSense components of PSoC4S are fourth-generation.

The AN85951 CSD(Self) and CSX(Mutual) has been described as up to 200pF as follows.

In addition, the description of the CapSense component datasheet has the following description.

Cp of CSD is up to 61pF.

From the above, both CSD(Self) and CSX(Mutual) does not mean support Cp of up to 200pF, I understand that  fourth-generation CSD is up to 61pF and CSX is up to 200pF. Is this recognition correct?

Or does CSD Auto mean up to 61pF and CSD Manual mean up to 200pF?

Regards,

I am trying to read the voltage of a battery using the SAR ADC but I am not getting the correct values. The ADC outputs 0x7FF0 no matter what the voltage is I am trying to measure. I am using a voltage divider with 357K ohm resistors and an input voltage of 3.8V though this can go as low as 2.5V. The ADC is using an internal Vref of 1.024V. Any help would be appreciated.

Hello 

I'm getting this error  (unknown type name 'CYBLE_API_RESULT_T')   in the BLE_StackGATT.h file.   I've updated my components as another post suggested.  A second post suggested to ignore the error but this is simply bad 

Hi,

Can we upgrade/edit the firmware of e78-868ln22s LORA end node using kitprog3 in modustoolbox or psoc creator??

Thanks,

Papendu