- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am new to PSoC and using PSoC4 CY8CKIT-049 kit. I tested it with LED blink program and its working fine. Now I tried to see result for ADC but I am getting error- Bootloader reported error 'Packet data invalid': The packet sent to the bootloader does not conform to the required packet format.
The program I wrote is a simple one. Programm inside for loop is:
aVal = ADC_GetResult16(0);
LED_Write(!LED_Read());
if(aVal> 2047) aVal = 2047;
if(aVal<1) aVal = 1;
aVal == aVal/2 +100;
CyDelay(aVal);
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Welcome in the forum!
This error is not related to the program you have written, it is a matter of communications between your bootloader which is already programmed into your kit and which cannot be overwritten.
Check the bootloadable component for the correct path to your original bootloader .hex and .elf files.
Check the baud rate settings
Triple check whether you took the correct com port
Check for the right blinking mode when kit was inserted with switched pressed.
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have checked again and again, but unable to find any error. Now when I am running my led blink program, it is showing the same error, but still the led is blinking. Not getting what is going wrong.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Can you please post your complete project, so that we all can have a look at all of your settings. To do so, use
Creator->File->Create Workspace Bundle (minimal)
and attach the resulting file.
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I have the same problem. After a working day with the kit, at the end the bootloader has sent me the same error, for all programs which had already worked .
Some additional info: I updated Psoc Creator to 4.0 and, also Cy_Boot to the last version together with the components according to Forum disscutions. The result is the same "Packet data invalid" for all my programs and for both kits. Should be a issue of configuration.
CY8CKIT 049 4125 AXI 483
CY8CKIT 049 4245 AXI 483
Please, give me an advice!
Thank You!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Danyi,
We are able to program your attached program once the dependencies are set correct.
To change dependency:
1. In the schematic view, right-click the Bootloadable component and select Configure.
2.In the configuration window, select the Dependencies tab and click the Browse button to point to the HEX and ELF files present in the ‘Dependencies’ folder under project directory. It will be present in the 49 kit specific files you have installed. Copy the complete path to the files in the appropriate fields.
This should solve the problem.
Best Regards,
VSRS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I am new to PSoC and using PSoC4 CY8CKIT-049 kit. I tested it with LED blink program and at the beginning it was working fine. After I tested with the CapSense project and CapSense proximity project it was also working well. But yesterday I added another project and now when I try to send my application on the board I am getting error- Bootloader reported error 'Packet data invalid': The packet sent to the bootloader does not conform to the required packet format.
So I tried uninstall and re-install PSoC Creator and started again with the SCB_Bootloadable project and now nothing is working and I have ALWAYS this error : "Packet data invalid ... "
Do you have any solution for me ?
Best Regards,
Agathe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Welcome in the forum, Agathe.
The project bundle does not contain all data.
Can you please post your complete project so that we all can have a look at all of your settings. To do so, use
Creator->File->Create Workspace Bundle (minimal)
and attach the resulting file.
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
At first: Some of your components are outdated. Use Creator -> Project -> Update Components. Repeat that for all your projects.
Make sure you are using the bootloader hex and elf file that came with your prototype kit because that is programmed into your chip (and cannot be changed easily).
Think about getting another (better) kit as the CY8CKIT-043. Main advantage (beside newer chip) is the ability for debugging your programs which can be a tremendous help.
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks a lot it works !
Agathe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Congratulations!
You are always welcome.
Bob