CY8CKIT147 PSoC 4100PS can't support WIN7

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
lili_285866
Level 1
Level 1
Distributor - Zenitron(GC)
5 replies posted 5 questions asked 5 sign-ins

Hi Sirs,

Customer use CY8CKIT147 the I2C Master to test Capsesnse(CapsenseMTKTool) ,But the driver can't support WIN7 ,Is there a driver that him to support  WIN7?

 

Thanks,

LIN

 

 

0 Likes
1 Solution
Hari
Moderator
Moderator
Moderator
750 replies posted 500 replies posted 250 solutions authored

Hi @lili_285866 

 

Can you take a look at this thread where the steps to re-install the drivers are mentioned - https://community.cypress.com/t5/PSoC-6-MCU/PSoC6-board-not-recognized-by-computer-after-failed-firm...

 

Adding the steps for reference - 

1. Right-click on 'KitProg' and select 'Update Driver Software'.

2.     Select 'Browse my computer for driver software'.

3.     Select 'Let me pick from a list of device drivers on my computer'.

4.     Click 'Next'.

5.     Click on 'Have Disk'. Please ensure that you do not miss this step.

6.     Browse and select the following file - C:\Program Files (x86)\Cypress\Programmer\drivers\KitProg2\KitProg2UART.inf

7.     After this, try 'Upgrade Firmware' in PSoC Programmer under the 'Utilities' tab.

 

Best regards, 
Hari

View solution in original post

0 Likes
4 Replies
Hari
Moderator
Moderator
Moderator
750 replies posted 500 replies posted 250 solutions authored

Hi @lili_285866 

 

The CapsenseMTKTool is not compatible with PSoC 4100PS. You can use the CapSense Tuner to tune and test the CapSense sensors for this device. Please take a look at any CapSense code example (eg CE210291 CapSense P4 One button) for details on using CapSense Tuner. 

 

Best regards, 
Hari

0 Likes
lock attach
Attachments are accessible only for community members.
lili_285866
Level 1
Level 1
Distributor - Zenitron(GC)
5 replies posted 5 questions asked 5 sign-ins

Hi Hari,

I mistake describe , I use new version psoc programmer can't find kitprog3 bridge driver for WIN7 ,but WIN10 can find kitprog3 bridge driver.

Thanks,

LIN

0 Likes
Hari
Moderator
Moderator
Moderator
750 replies posted 500 replies posted 250 solutions authored

Hi @lili_285866 

 

Can you take a look at this thread where the steps to re-install the drivers are mentioned - https://community.cypress.com/t5/PSoC-6-MCU/PSoC6-board-not-recognized-by-computer-after-failed-firm...

 

Adding the steps for reference - 

1. Right-click on 'KitProg' and select 'Update Driver Software'.

2.     Select 'Browse my computer for driver software'.

3.     Select 'Let me pick from a list of device drivers on my computer'.

4.     Click 'Next'.

5.     Click on 'Have Disk'. Please ensure that you do not miss this step.

6.     Browse and select the following file - C:\Program Files (x86)\Cypress\Programmer\drivers\KitProg2\KitProg2UART.inf

7.     After this, try 'Upgrade Firmware' in PSoC Programmer under the 'Utilities' tab.

 

Best regards, 
Hari

0 Likes
lili_285866
Level 1
Level 1
Distributor - Zenitron(GC)
5 replies posted 5 questions asked 5 sign-ins

Hi Hari, 

I try use winusbcompat.inf driver can find i2c bridge. 

Thanks,

Lin

 

 

0 Likes