Nor Flash Forum Discussions

Datasheet Rev L,

In table 8 the size of CFI data and the byte address range are not consistent. Range 00020h~000CEh (Here is also a typo in the table) means the size = 206d - 32d + 1d = 175 but the table scribed 174 which is confusing. 

Also, is the ID/CFI ASO support Continuous & Linear Synchronous Read? The datasheet mentions SSR support both async/sync read but doesn't tell if ID/CFI supports it or not. 

Thank you.

Regards,

Keter

I have 50 pcb-s where I can't read device and manufacture ID
component soldered, ABA analysis carried out, error goes with component
What could be the reason?
Another batch of components works without problems.

#DEFINE READ_ID WD=0x9F RD=MAN_ID RD=DEV_ID CE_HI
#MAN_ID=0x34
#DEV_ID=0x2A

pass
*** No precondition file present ****
**** Manufacturer ID matches ****
Found: 0x34, Expected: 0x34

**** Device ID matches ****
Found: 0x2A, Expected: 0x2A

fail
**** Manufacturer ID ****
Scan path malfunction
**** Device ID Error ****
Found: 0x0, Expected: 0x2A

I think the difference between S29AL016J70TFI010 and S29AL016J70TFI020 is the difference between top boot sector device and bottom boot sector device. Is there any revision required when using S29AL016J70TFI010 when using S29AL016J70TFI020?

Hello. The device is using the S29JL064J60TFI000 flash device.

What is the MTBF / failure rate for this device?

Hi There,

I will use "S29GL01GS10TFI010".
It is connected to the FPGA in parallel.
(FPGA = MAX10 Series)

We are looking at ways to program the device.
Is there provided to programming tools the NOR flash ?

Best regards
- satoshi

I need to read the Ready/Busy [RY/BY#] signal with a 3.3V device. Can I pull-up to 3.3V when the IO voltage is 1.8V? Save a level translator if I can without damaging the device.  It is open drain and the core reference is 3.3V but the IO is 1.8.  I don't see this documented in the data sheet.

S70GL02GT is the memory type

S25FL064L , S25FL128L

Are the areas that can be locked with a password as follows?

　Security area 2 (256 bytes with an address range of 200 to 2FF)

　Security area 3 (256 bytes with address range of 300 to 3FF)

BR

Toshinari Ikeuchi/TED

Is it possible to download the full version of the datasheet for S25HL02GTDPBHB053.

Unable to read manufacture ID, and ERASE not working

Dear Sir/Madam,

GreenSoft Technology, a leading provider of environmental compliance data management services and software for the global electronics industry (http://www.greensofttech.com), has been contracted by Radisys to collect compliance data on parts purchased from your company. Please refer to attachments for a letter of authorization from Radisys and a list of part numbers.

Please note that Radisys might not purchase directly from your company but via a reseller or distributor. In addition, you may need to collect material or compliance documents from your suppliers such as raw material manufacturers to fulfill this request. Your support to Radisys is highly appreciated.

Can you please provide the following environmental compliance data for these parts:

• RoHS 2(2015/863/EU and 2011/65/EU) Certificate of Compliance (CoC); template is attached. Directive 2015/863/EU, published June 4, 2015, amends RoHS 2 2011/65/EU to include 4 additional restricted substances.
• Full Material Disclosure (FMD), MSDS or similar document in your standard format if available
• REACH Declaration or SVHC Certificate; REACH SVHC 219 and 211 templates are attached.
• CA Prop65 Certificate of Compliance (CoC); a template is attached.
• If reportable SVHCs are identified, Substances of Concern In articles as such or in complex objects (Products) (SCIP – per Waste Framework Directive 2008/98/EC, amended by Directive (EU) 2018/851)
• Lifecycle Status

Generally, the parts applicable for 6a/6b/6c RoHS alloy exemptions would form an article, such as a pin, connector shell, standoff, screw, or bracket. Therefore, Lead concentration of such parts is likely to exceed 1000ppm at Article level, which needs your further support to provide the SCIP information. However, if you confirm your products are SVHC compliant, please provide the Article Name.

If you cannot recognize a part or it's incorrect, please indicate such in your feedback.

Please respond as soon as possible or provide an expected date of completion and we will follow up. We may contact you if any clarification is needed. Radisys is committed to providing its customers with products that meet the highest standards of innovation, performance and environmental safety and expects your timely response.

If you have any questions, you can contact me at Cora@greensoft-china.com or call +1 323-254-5961 x813 (I am based in China; we also have someone in our US office that can answer your questions).

Best Regards,

Cora Zhang

Project Engineer

Cora@greensoft-china.com

GreenSoft Technology, Inc.

155 S. El Molino Ave, Suite 100,

Pasadena, CA 91101, USA

Ph: 323.254.5961

www.greensofttech.com

GreenSoft Technology – China Office

No 368, North Xinshi Rd, FL12

Shijiazhuang,Hebei, China

Ph: +86-311-8386-4638