Nor Flash Forum Discussions
I am writing firmware to interface with NOR Flash S70FL01GS using Nordic SDK and ARM chip. Where can I find example source for SPI communication with NOR Flash?
Show LessHi,
I am using the flash chip of CYPRESS, S25FL128SAGMFI000, but I have some questions that I don't understand .
After power up, I did the RDSR1 command to read the value of the Status Register 1 , I thought the SR1 value should be "00"H, but the result was "81"H.
(I did nothing after the chip was powered up, only read the SR1, besides, the RESET# was not used and was unconnected)
Could you help with to figure out why this happened?
here is the picture of the question.
Show Less
how to program Advanced Sector Protection for S29GL128P, need examples
Hi,
I am looking for counterparts list of current Micron parts.
I found the below link but part number does not match completely. So, please let me know if cypress have appropriate parts.
Best regards,
Shohei
Show LessHello Cypress community,
I want to use S25FL256SAGMFI003 SOIC-16, with 1.8V procsessor. I had a doubt about 1.8V working because I faced with this sentence "For a backward compatible SO16 footprint, the VIO supply is tied to VCC inside the package; thus, the IO will function at VCC level." in datasheet could you please help me to clarify the right meaning of this sentence and whether can i use this package with 1.8V or not?
Sincerely yours,
Siyavash
Show LessHello,
NOR Flash with automatic ECC function will generate valid ECC code when issuing the Write Buffer Programming command.
On the other hand, when executing the Single Word Programming command or overwriting data on the same page, the ECC code is invalid.
At this time, if data is read, can the data be read while ECC is invalid?
Or is the data itself read invalid?
MPN S29GL01GT10TFI010
Best Regards,
Naoaki Morimoto
Show LessHi
I am using the flash chip of CYPRESS,S25FL128SAGNFI000, but I have some questions that i don't understand when I do the simulation.
I am doing the simulation of QPP command, but when I do the QPP command for several times , there are some of the cases that indicate there is a program error happen.
but these cases are the same except the address and the write data, So could you help me to find out why the program errors happen?
(the commadn execution is this:
the system send the qpp signal, then the FLASH control module send the commands to the flash chip like this sequence:
1, WREN+RDSR1 (make sure that the WEL is enable)
2, QPP+ADDRESS+DATA(quad mode, 32bit data )
3, RDSR1(polling to check the WIP ) )
But,
1, I do the qpp command like 6 times , the only differece between these cases is the different address and different wite data.
But just like the figure, at the 2nd and 3rd time, the program error happened.
and after the QPP + ADDRESS+DATA, then the first RDSR1, the SR1[6] is 1...
But I don't know why the program error happened...
Could you help me with the question?
Thanks again and looking forward to your reply~~~
Show LessAlthough the definition of the Typ value and the Max value is stated in Note 1, is it OK to say that it approaches the Typ value at 100,000 time P / E cycles and approaches the Max value at 1000,000 time P / E cycles ?
In Note 6, 100,000 cycles are stated as the Min value of the P / E cycle, but what problems will arise if it exceeds 100,000 times?
Show Less
Is the content below wrong?
If you make a mistake, will you fix it?
■ Page 23: PL 127 J Sector Architecture
Although it is described up to SA111, it is SA115 on the next page.
■ Page 26: PL 127 J Sector Architecture
Although it is described up to SA 210, it becomes SA 213 in the next page.
■ Page 48: PL 064 B Boot Sector / Sector Block Address for Protection / Unprotection
There is no mention only until SA 138.
■ Page 73: Toggle Bit Algorithm
Notation is different from past data sheet and other varieties.
■ Physical Dimensions
There is a PKG whose thickness (A2) is not specified.
hi.
I found information about NOR Flash in the following document.
http://www.cypress.com/file/275051/download
P. 23 3.3.5 NOR Flash
And I want to use this, but I can't find any sample programs of S25FL132K.
I found sample programs of S25l164K(FM_PDL_2.0.1/example/hsspi/hsspi_access_s25l164k),
but it doesn't work on FM0+.
Where is the document which shows me how to use S25FL132K ?
thanks.
Show Less