- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I was searching for the Tees (Evaluate Erase Status) and Ters (Erase Resume to Next Erase Suspend) parameters in the S29GL512P datasheet, but haven't found them. Do you know what the values for these parameters are?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Thank you for contacting Cypress Semiconductor.
In regards to Sector Erase/Chip Erase operation, refer to pgs. 25 to 27 (sections 7.7.3 - 7.7.4)
In regards to Program/Erase Suspend-Resume operation, refer to pg. 28 (Section 7.7.5)
In regards to checking/reading Erase status, refer to pgs. 31 to 34 (sections 7.8.1 - 7.8.6)
For Timing Diagrams :
Data# Polling & Toggle Bit Timings (During Embedded Algorithms), refer to pgs.58 to 59 (Figs. 11.12 - 11.13
There is no minimum or maximum time requirement between Erase Suspend to the next Erase Resume.
The time in which the Erase Suspend is initiated and when Erase Resume is initiated is user defined.
URL to S29GL512P datasheet :
https://www.cypress.com/file/219926/download
Best regards,
Albert
Cypress Semiconductor Corp.
An Infineon Technologies Company
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Thank you for contacting Cypress Semiconductor.
In regards to Sector Erase/Chip Erase operation, refer to pgs. 25 to 27 (sections 7.7.3 - 7.7.4)
In regards to Program/Erase Suspend-Resume operation, refer to pg. 28 (Section 7.7.5)
In regards to checking/reading Erase status, refer to pgs. 31 to 34 (sections 7.8.1 - 7.8.6)
For Timing Diagrams :
Data# Polling & Toggle Bit Timings (During Embedded Algorithms), refer to pgs.58 to 59 (Figs. 11.12 - 11.13
There is no minimum or maximum time requirement between Erase Suspend to the next Erase Resume.
The time in which the Erase Suspend is initiated and when Erase Resume is initiated is user defined.
URL to S29GL512P datasheet :
https://www.cypress.com/file/219926/download
Best regards,
Albert
Cypress Semiconductor Corp.
An Infineon Technologies Company
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks! I noticed that the datasheet for the S29GL512T defined a typical erase resume to next erase suspend time, but the S29GL512P datasheet didn’t. Is there a difference between the typical erase resume to next erase suspend time in these parts?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
Yes, there is a difference between the S29GL512T and the S29GL512P, as the S29GL512T has a built-in Embedded Algorithm Controller (EAC), which the S29GL512P does not have. Therefore, ~100uS(min) delay is required when the PROGRAM or ERASE RESUME command is initiated to allow the EAC to complete any remaining PROGRAM or ERASE operation to full completion, before the next SUSPEND mode can be initiated.
The S29GL512P does not have an internal EAC.
Best regards,
Albert
Cypress Semiconductor Corp.
An Infineon Technologies Company