cancel
Showing results for 
Search instead for 
Did you mean: 

ModusToolbox General

walo_4223926
New Contributor

May I ask how to solve the following problems? Thank you very much!

1. OS Version: Window 10 64bit

pastedImage_0.png

2. ModusToolbox_1.1 installation directory :C:\Users\shiha\ModusToolbox_1.1,

pastedImage_1.png

3. ModusToolbox_1.1 WorkSpace directory:C:\Users\shiha\mtw

pastedImage_9.png

4. New project:

   4.1. File->New-> ModusToolbox IDE Application,select the following figure:

     pastedImage_17.png

  1. 4.2. Application, select the following figure.

       pastedImage_18.png

          4.3. Click Next:

         pastedImage_20.png

          4.4. Click Finish:

         pastedImage_22.png

         4.5. WorkSpace directory:

          pastedImage_25.png

    5. Open design.modus as follows:

       pastedImage_29.png

     6. Do not do any change option ,click save directly,prompt to go down:

      pastedImage_32.png

       7. Click OK,as follows:

      pastedImage_35.png

0 Likes
1 Solution
Roy_Liu
Moderator
Moderator

The issue is resolved in the earlier mentioned discussion Re: ModusToolBox can't compile the example project correctly without any change by using the method below:

1. check if customer has an environment variable set - JAVA_HOME. If so, remove it and check if this issue still there.

2. if issue still there, set that environment variable JAVA_HOME=C:\[your path here]\ModusToolbox_1.1\tools\jre-1.0 fix the issue?

Roy Liu

View solution in original post

9 Replies
Roy_Liu
Moderator
Moderator

Can you re-post the pictures #4.4,5,6 and 7 with higher resolution, the message in the current ones are not readable.

Roy Liu
0 Likes
walo_4223926
New Contributor

How can I repost the picture to make it more clear? Thank you very much!

  • Is it convenient for you to provide email address?
0 Likes
HaoW_21
Employee

Attached initial report for this issue.

Hao

0 Likes
Roy_Liu
Moderator
Moderator

Are you using the MODUSToolBox version of this?

pastedImage_1.png

Can be downloaded from https://www.cypress.com/products/modustoolbox-software-environment

Roy Liu
0 Likes
HaoW_21
Employee

Hi Roy,

Yes, customer is using this version. This issue can only be reproduced on customer laptop, does not have issue with our laptop. I remotely confirmed this issue, currently have no idea what could be wrong.

Hao

0 Likes
Roy_Liu
Moderator
Moderator

WangS_81​ have you been seen this issue before?

Roy Liu
0 Likes
ShipingW_81
Moderator
Moderator

Not sure about the root-cause.

However, there is another thread in which reports a similar issue - Re: ModusToolBox can't compile the example project correctly without any change

It also shows error - "Unable to evaluate parameter ‘Multiplier(1-262143)’ on personality 'FLL'".

Note that customer also uses Win10 64bit(simplified chinese version).

0 Likes
HaoW_21
Employee

Fred,

This is the same issue.

Hao

0 Likes
Roy_Liu
Moderator
Moderator

The issue is resolved in the earlier mentioned discussion Re: ModusToolBox can't compile the example project correctly without any change by using the method below:

1. check if customer has an environment variable set - JAVA_HOME. If so, remove it and check if this issue still there.

2. if issue still there, set that environment variable JAVA_HOME=C:\[your path here]\ModusToolbox_1.1\tools\jre-1.0 fix the issue?

Roy Liu

View solution in original post

Top labels