- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello I am new to Cypress.
I am using kit CY8PROTO-062-4343W
I would appreciate your help
I am following the videos getting starting https://www.cypress.com/video-library/PSoC-Software/modustoolbox-101-lesson-1-2-blinky-led/610051
1. I try to find blinkLed and is not there. Do you know where I can find it?
2. When I creating a new Application, I click New application then I chose "CY8PROTO-062-4343W", "Hello world" Example. when open the device configurator 2.1 and click the tap pins, the IDE shows me a different MCU the (CY8C6245LQI-S3D72). This is not correct. How I can fix this error? thank you
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
1
I make the program from "Empty PSoC6 App" as follows:
#include "cy_pdl.h"
#include "cyhal.h"
#include "cybsp.h"
int main(void)
{
cy_rslt_t result;
/* Initialize the device and board peripherals */
result = cybsp_init() ;
if (result != CY_RSLT_SUCCESS)
{
CY_ASSERT(0);
}
__enable_irq();
for (;;)
{
Cy_GPIO_Inv(LED_RED_PORT, LED_RED_PIN);
Cy_SysLib_Delay(1000/*msec*/);
}
}
The setting of Device Configuration is as follows:
Unfortunately, I don't have a board, so I would appreciate it if you could check it and report it.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi maos_4728266,
1
Unfortunately, I haven't found the program.
It's a very simple program, so edit main.c directly.
2
When you created a new Application, did you select "CY8PROTO-062-4343W"?
I can select CY8C624ABZI-D44 which is used in CY8PROTO-062-4343W at Device configuration2.1.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
1
I make the program from "Empty PSoC6 App" as follows:
#include "cy_pdl.h"
#include "cyhal.h"
#include "cybsp.h"
int main(void)
{
cy_rslt_t result;
/* Initialize the device and board peripherals */
result = cybsp_init() ;
if (result != CY_RSLT_SUCCESS)
{
CY_ASSERT(0);
}
__enable_irq();
for (;;)
{
Cy_GPIO_Inv(LED_RED_PORT, LED_RED_PIN);
Cy_SysLib_Delay(1000/*msec*/);
}
}
The setting of Device Configuration is as follows:
Unfortunately, I don't have a board, so I would appreciate it if you could check it and report it.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Nota
Thank you so much, I tried and it worked, I also tried using the HALS functions and using the configuration that you noted and it worked as well.
#include "cy_pdl.h"
#include "cyhal.h"
#include "cybsp.h"
int main(void)
{
cy_rslt_t result;
/* Initialize the device and board peripherals */
result = cybsp_init() ;
if (result != CY_RSLT_SUCCESS)
{
CY_ASSERT(0);
}
__enable_irq();
for (;;)
{
cyhal_gpio_toggle(LD4_RED_HAL_PORT_PIN);
cyhal_system_delay_ms(500);
}
}
/* [] END OF FILE */
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Congratulations!
I was relieved to hear your report.
Thanks,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi, I beleive answe from @NoTa_459116 was helpful in Q#1.
Regarding Q2, please can you reproduce the issue with following the steps to create an new MTB project ? y
I repeated the steps today to create a hello world program and couldn't reproduce the issue you mentioned. Please find the screenshot here below to see the correct target IC selected.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Ravikiran.
it seems that I was doing something wrong. I checked it again and everything is working great.
Thank you so much for your help.