Microcontrollers Forum Discussions

请教大家一个问题

我现在做的boot程序在跳转app程序的时候，如果boot程序和app程序都没有使用中断的情况下可以正常跳转，但是boot程序或app程序有一方面使用中断的话就会进入到debug，boot程序或app程序单独运行时没有问题。下面按照串口中断举例。

调试状态下会卡在下图位置：

我想知道是哪个地方设置的不对或者少设置了什么地方。

Hello,

We are developing the bootloader for the Infineon TC377 board.  For that, we need the preserved RAM (The memory that shouldn't be initialized with zero during the controller reset) to hold the flag. So, we tried the keywords below for No-initialization and location, but AURIX is not supporting these keywords. Instead of the below keywords, what can be used to create the memory in the RAM, so that it shouldn't be modified after reset of the microcontroller.

#pragma NOINIT(BootMode_InPreservedRAM)

#pragma LOCATION(BootMode_InPreservedRAM,0x50000000)

/*Here first we are creating the variable BootMode_InPreservedRAM as no initialization and giving the address as 0x50000000 for LOCATION*/

Thanks in advance.

I am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall  cysecuretools i got the message stating command already satisfied.  This is all done on Windows. 

My purpose is to control the private server motor. Because most servo motors are controlled using pulses. So if it involves the acceleration and deceleration of the motor, the interval between each pulse may be different. Therefore, every time the timer is interrupted, the entry time of the next timer will be changed. In STM32, I can make the time into a list. Then directly import the register TIM3->ARR = tim[X]. However, it was found that in XMC1302, it is not allowed to write values directly to the register. But need to use

TIMER_Stop(&TIMER_0);
status = TIMER_SetTimeInterval(&TIMER_0, tim[ X ]);
if (status == TIMER_STATUS_SUCCESS)
{
        TIMER_Start(&TIMER_0);
}

This is how you can reset it. But this code runs too slowly. About 60US. This is obviously too long. Is there a faster way?

Hi Infineon team,

      In some of our designs we use the SAK-C167CR-LM-HA+ microcontroller. Can we use SAF- C167CR-LM in place of it?

Are SAK-C167CR-LM-HA+ and SAF- C167CR-LM functionally equivalent? On page 59 of the datasheet, I can see that ambient temperature rating is different between SAK and SAF prefixes. Other than this are there any differences? What does the "HA+" stand for?

Thank you.

Regards,

Abhijeet B

Hello,

Recently if I open PSoC Designer normally (not as admin) I can open projects but the top file menu ribbon is not available and I can't do any build or debugging.

If I run Designer as admin then the project does not open and I get this error:

has anyone had this problem? Any help is appreciated.

hi, while building the project am getting following error.
make[1]: *** [../mtb_shared/core-make/release-v3.0.3/make/core/build.mk:435: C:/DemoProject/build/CY8C6245LQI/Release/AIController-Psoc6.elf] Error 1
make: *** [../mtb_shared/core-make/release-v3.0.3/make/core/main.mk:376: secondstage_build] Error 2

I tried reinstalling the Modustoolbox, also corrected the path of Environment variable, but nothing seems to be working.

Hii,

I'm using CYTVII-C-2D-6M-327-SET evaluation kit for my project.   I require information's about pinout details exposed out in dev kit and its schematic diagram .

I couldn't get those documents.  could you support on this ?

Thanks.