Connecting the RESET# Signal to IO3/RESET# Signal on S25FL-L, 16-Pin SO and 24-Ball BGA Packages – KBA219553
- Subscribe to RSS Feed
- Mark as New
- Mark as Read
- Bookmark
- Subscribe
- Printer Friendly Page
- Report Inappropriate Content
JP Translation:S25FL-L、16ピンSOおよび24ボールBGAパッケージのIO3/RESET#信号へのRESET#信号の接続 - KBA219553
Version: **
Question:
Can the RESET# input signal be connected to the IO3/RESET# input signal on the S25FLxxxL, 16-pin SO and 24-ball BGA package?
Answer:
Yes, theoretically, and only for certain use cases; this is not best practice.
Although the RESET# and IO3/RESET# can accomplish the same hardware reset function for certain flash use cases, it is not recommended to connect RESET# with IO3/RESET# for the higher pin count (> 8 pin) packages — even if you will never use the IO3 pin function. For these packages, the best practice is to use the separate, dedicated, RESET# connection.
The multiplexed IO3/RESET# pin warrants a closer look for the 8-pin packages because there is no spare pin for a dedicated RESET# signal when the package is limited to 8 pins.
There are actually two controls shown in the FL-L datasheet (002-12878 Rev B) for the IO3/RESET# pin. The first control in Configuration Register 2 is CR2xV[7] = IO3R:
Setting this bit to 0 disables the multiplexed IO3/RESET# function, so this pin is always IO3 and the RESET# function is always disabled. Setting this bit to 1 enables the multiplexed IO3/RESET# function, so the function of this pin is chosen by the QUAD bit.
The second control is in Configuration Register 1 CR1xV[1] = QUAD:
So, if CR2xV[7] = IO3R = 1, then the multiplexed IO3/RESET# pin has the RESET# function while QUAD=0 and it has the IO3 function when QUAD = 1.
- Tags:
- a25l
- a25lq
- adesto
- amic
- at25bcm
- at25df
- at25dl
- at25dn
- at25f
- at26df
- bga
- competition
- competitor
- configuration register
- cypress
- cypress flash memory products
- dio
- dual data rate
- en25b
- en25f
- en25p
- en25q
- en25qh
- esmt
- f25l
- f25s
- float
- floating gate
- gd25q
- gigadevice
- hardware reset
- high
- hyperbus
- hyperflash
- hyperram
- input
- interface
- io
- io3reset
- is25cq
- is25ld
- is25lq
- issi
- k8a
- k8c
- k8d
- logic
- low
- m25p
- m25pe
- m25px
- macronix
- manufacturers part number
- micron
- miso
- mosi
- mpn
- mx25l
- mx25v
- n25q
- nor flash memory
- nput
- opn
- ordering part number
- output
- package
- pull up
- qspi
- quad data rate
- quad io mode
- reset
- resistor
- s25fl064l
- s25fl128l
- s25fl256l
- samsung
- serial
- serial flash
- serial nor flash memory
- serial peripheral interface
- settings
- single data rate
- so
- soic
- spansion
- spi
- tc58nvg2s0hbai4
- technology
- toshiba
- unconnected
- vih
- vil
- voh
- vol
- voltage
- w25q
- w25x
- w29gl
- winbond