Microcontrollers Forum Discussions

What's the different between infineon's CAM sensor TLE4983, TLE4986, TLE4988, TLE4931?

Thanks

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/CAPSENSE-MagSense/Infineon-CAM-sensor-Type/td-p/744491

I am using the  CY8CKIT-059 PSoC 5LP Prototyping Kit  for a project, and I'm very new to this. I have been a LabVIEW programmer for ten years, so I'm trying to get back into C and also using this device for the first time. So, I'm sorry for the basic questions. 

I have a HD44780 1602 LCD display that I thought would work for this. I've loaded the CharLCD_CustomFont project for the PSoC 5LP device. The port (P2) and the pins seem to coincide with how I've connected them to the display.

I have attached some documentation for reference.

I get no characters displayed on the LCD. I've connected an analyzer to the LCD pins to verify that they are all at least changing--the LCD enable is being activated, R/W is changing, etc. I have not yet found the file where the P2 pins are assigned their purpose to verify the settings are correct. I'm still trying to get oriented with all the code with this project.

If anyone has used this display, or something similar and has some input, or you might have an idea why characters are not being displayed, I would greatly appreciate any input.

Regards,

Dayle

大家好，

     最近想用keil调试cyt2bt73cae这个芯片的程序，使用mtb导出的工程只有单核应用，然后device这里显示

，这种导出的工程直接是CM4的，编译过后能够达到使用CM0启动CM4的效果？如果不能，我应该怎么做？

 当我配置了cm0plus以后，cy_m0p_image[]这个数据的含义是什么，需要我手动调用吗？ 

当我使用导出的keil工程的GPIO中断时，无法进入终端服务函数，这和我没有CM0有关系吗？

希望有人能够帮到我，感谢~

hi, while building the project am getting following error.
make[1]: *** [../mtb_shared/core-make/release-v3.0.3/make/core/build.mk:435: C:/DemoProject/build/CY8C6245LQI/Release/AIController-Psoc6.elf] Error 1
make: *** [../mtb_shared/core-make/release-v3.0.3/make/core/main.mk:376: secondstage_build] Error 2

I tried reinstalling the Modustoolbox, also corrected the path of Environment variable, but nothing seems to be working.

请教，我目前正在使用的是，XMC4800_E196K2048的芯片，工程是ETHCAT_SSC_AUT_BASE_XMC48，我在这个工程上添加了，PMSM_FOC的模块，但U,V,W三相引脚，无法配置P0_0,P0_1,P0_2,P0_3,P0_4,P0_5,这六个引脚。但我明明没有使用这个六引脚啊，为什么无法配置啊，请看附件。

hi，大家好

目前在使用Psoc6 ble开发板开发，M0核和M4核都有使用，分别建立了工程，在各自的核擦写都是成功的。现在遇到的问题是用M0核做boot loader，跳转到M4核执行App后，擦写就会失败 。请帮忙看看，谢谢谢谢！

Hi !

I'm working on Tricore Tc397 SPI.

It appears like datawith is 2-32bits.

Is there a way to send over SPI in one frame with more than 32bits for example 64bits?

One frame here i mean is CS stays low and SCLK is continuous.

Hi I'm using TLE9879 as pump, FOC driver. pwm frequency 16K. in one-match interrupt update down count compare value, period match interrupt update up count compare value with FOC algorithm. period match interrupt execution at 24us everything is fine, at 29us there is an exception, as shown in the image. The timing of the one-match interrupt and the period interrupt seems to be out of order.

Hi,

I'm looking for an complete example for using an external memory  (CY15B104QSN) with DSPI in modusToolbox.

My test board is the KIT_XMC72_EVK XMC7200 evaluation kit.
I did find a lot of code snippets, but none of them are complete using the device configurator and the QSPI configurator and finally having all steps from the initialisation till reading and writing from/to the device.

The board connector is J21 which I use.

Support is highly aprechiated.

BR

Martin