Featured Discussions
Greetings,
Kindly provide the TLE5012B (GMR BASED ANGLE SENSOR) and TLE49681M (HALL SENSOR) Zero position programming for our reference to work.
I procured these sensor from Infineon last week.
Kindly send me the file for the programming.
Show LessHi IFX,
Chip :cyw43455
1.Below setting can connected to AP1(WPA2+802.11r) .
network={
ssid="80211Rtest"
proto=RSN WPA
key_mgmt=SAE FT-PSK WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="12345678"
}
2. disconnected to AP1(WPA2+802.11r)
3.connected to AP2(WPA3) :CYW43455 can not connect to AP2(WPA3).
Is it impossible to connect to AP2(WPA3) after adding FT-PSK in wpa_supplicant.conf ?
If yes, could you give me some guidance about waht wpa_supplicant.conf setting support AP1(WPA2+802.11r) and AP2(WPA3) .
We want the same wpa_supplicant.conf setting for AP1(WPA2+802.11r) and AP2(WPA3) .
B.R.
Bill.
Show LessHello, we bought a Siemens thermal resistance tester and found that the testing of Infineon modules is quite different from the specification? Can you tell me if the Infineon thermal resistance test is also done with the Siemens machine? Is it water cooled?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/%E8%A5%BF%E9%97%A8%E5%AD%90%E6%9C%BA%E5%99%A8IGBT%E6%A8%A1%E5%9D%97%E7%83%AD%E9%98%BB%E6%B5%8B%E8%AF%95%E5%80%BC%E5%81%8F%E5%B0%8F/td-p/716545
Show LessHi, I am using the Psoc 4100 s max microcontroller in which CY8C4149AZI-S598 mcu used. Can you please help in finding out which pins we can configure for SPI communication in this microcontroller. I am unable to find out these and also dont have pinout diagram for that.
Show LessHello, We have FS100R12W2T7 module in use, but the module Datasheet doesn't have SC data labeled TC=25C, can I simply calculate the short circuit current for TC=25C based on the trend of 175C-150C?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/IGBT-Datasheet-SC-data/td-p/716531
Show LessI reconfigure the firmware in config.h: I just modify the bandwidth into 0MHz ,I try to transmit signle tone with my board.
And I also flash the new .hex file inro my board successfully with XMC Flasher.
When I reconnect my board with new FW into my PC, it's LED just like this, only one yellow LED lighting
And when I open GUI, it show no Device connected, and my matlab code also can't run:
Then how can I know this radar still work and really the bandwidth is 0MHz. And if it's still working, I want to extraxt raw data with my matlab code? How can I modify the original code? I really need help, thanks!
Show Less
Hello Team,
I walk through the TC375XX tricore infineon Micro safety manual, I see lot of internal and external software and hardware safety mechanisms.
My understanding is that the Internal and external safety mechanisms would be implemented and prevented against the safety Goal. I would like to know what the MCU safety Goal are or is there any Assumptions of use case considered? please clarify.
Regards,
Nallusamy