Featured Discussions
Hi Sir
we knew that there are two roaming way of 80211r , one is over-the-ds , the other is over-the-air.
Is it possible that disable over-ther-ds , and keep over-the-air function ?
Show Less
Help!
Customer said my label is not original. Please help to verify. Thank you!
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/MOSFET-Si-SiC/IRFR9024NTRPBF-label-question/td-p/723829
Show LessHi there,
may I ask
1. Does IFX WiFi 2.4G support 18.5dbm power solution?
2. Does IFX BT support apple find my and does it support Android?
Thank you!
Mason
Show LessHi, experts.
When debugging Infineon example "Flash_Programming_1_KIT_TC334_LK ", I found that when I used the default parameters, Flash can be erased normally, but when I changed the initial address of erase from 0xA00E0000 to 0x80080020, I found that the erase seemed to fail. when I changed the initial address of erase from 0xA00E0000 to 0x80080020, I found that the erase seemed to fail, I think it may be caused by the macro definition "#define RELOCATION_START_ADDR (0x70100000U) ", please tell me what this macro definition means, and how to solve the problem here, thank you!
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/The-Infineon-example-quot-Flash-Programming-1-KIT-TC334-LK-quot-failed-to-erase/td-p/723792
Show LessDear.
What is the difference between configuring full measurement as 0, or 1 in Lib_Meas_Fast_Sample function?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E5%8E%8B%E5%8A%9B%E4%BC%A0%E6%84%9F%E5%99%A8/SP49-full-measurement%E9%85%8D%E7%BD%AE/td-p/723774
Show Less我现在有6路pwm波,A、B、E、F、G、H,这六路pwm需要同时调频移相,我的B、E需要基于A移向,F需要基于E移相,G和H需要基于E移相,但是GTM-TOM模块pwm同时输出并满足移相有两种情况,一种是都基于A去移相,一种是基于前一个通道去移相,一旦我使用第一种,我的F基于A移相就会超过50%,这将导致PWM出现一个周期的高电平的波形,如果使用第二种我又无法满足我的移相标准,请问是否可以混合使用这两种模式,怎么使用?
祝好!
Show LessHi all,
We are evaluating EVAL_TDA38740_3.3VOUT.
Please check the attached file for the measurement circuit, register settings, component changes, and measurement conditions.
We would like to prevent the output current from jumping up due to sudden changes in the output voltage.
Is it possible to smoothly ramp up to the setting voltage?
If not, can you calculate the value of the jump voltage?
Best regards,
MS
Hi guys,
So I've done to set the serial number in fx3 as this KBA
But I have a question, so we are integrating the FX3 in our custom board which each serial number its about 12 characters,
and I tried to just write the Serial number as this:
const uint8_t CyFxUSBSerialNumberDscr[] __attribute__ ((aligned (32))) =
{
0x10, /* Descriptor size */
CY_U3P_USB_STRING_DESCR, /* Device descriptor type */
'M',0x00,
'Y',0x00,
'C',0x00,
'A',0x00,
'R',0x00,
'D',0x00,
'1',0x00,
'6',0x00,
'0',0x00,
'5',0x00,
'9',0x00,
'3',0x00,
};
But this will only show as:
How can I make it to look as the full serial number?
Thanks!
Show Less