Featured Discussions
Dear Supporter
I want to translate the following KBA. Please confirm to my work.
TRAVEO™ T2G MCU: Protection context (PC) requirements for system calls – KBA239469
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
TRAVEO™ T2G MCU: Analyzing T2G devices in DEAD state – KBA239492
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
AURIX™ MCU: GETH embedded MTL queue FIFOs handling - KBA239698
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
AURIX™ MCU: Possible combinations of error flags in SENT module – KBA239730
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
ModusToolbox™ "make" command hangs – KBA239829
Regards,
Kazuki
Show LessHi,
I have a AURIX MotorControl Application Kit with TC234LF, I want to switch from ADS to Visual Studio Code. I'm going to make it through the GCC compiler, but there is a problem using the winIDEA debugger. WinIDEA requires a license. I did not find a price list on the website and how to buy it.
Are there alternative debuggers that can be used in Visual Studio Code?
AN84868 is followed to implement using CX3 to configure FPGA. To be able use the FPGA configuration utility tool, descriptors are the same for AN84868 for FPGA configuration application firmware. After FPGA configuration, firmware switches to CX3 UVC application. FPGA configuration part is good, after switching to UVC application, video streaming is also good. Yet, UART is not able to send out debug information anymore in UVC application. UART debug works during FPGA configuration and printout information on data count for FPGA configuration process.
IO matrix configuration is the same for FPGA configuration application and for UVC application, i.e. I2C, SPI and UART peripherals are all enabled.
I am using GPIO 48 to 49 as the UART tx and rx.
What could be the problem?
Thank you for help in advance.
Show Less
As the title suggests, it's easy to implement in interrupt, but what should I write if I want to implement it in a general function? I didn't find any flag bits that I can use directly, but buffer has NDAT that I can determine directly.
The RF0N of the FIFO is under IR, I use this flag bit for judgment, and after 103 normal sends I get buserror.
How to realize this function?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E4%BE%8B%E7%A8%8B/CAN%E6%80%8E%E4%B9%88%E9%80%9A%E8%BF%87FIFO%E5%9C%A8%E6%94%B6%E5%88%B0%E6%8A%A5%E6%96%87%E5%90%8E%E5%86%8D%E6%8A%8A%E8%BF%99%E6%9D%A1%E6%8A%A5%E6%96%87%E5%8F%91%E9%80%81%E5%87%BA%E5%8E%BB/td-p/744593
Show LessHi,
I want to translate the following App Note to Japanese. Please confirm to my work.
"Getting started with 2ED2410-EM"
URL: https://www.infineon.com/dgdl/Infineon-2ED2410-EM-ApplicationNotes-v02_01-EN.pdf?fileId=8ac78c8c80f4d3290181235b7ca11c3a
Best Regards,
Hayashi.K