Featured Discussions
If i purchase KIT_A2G_TC399_5V_TRB_S HW then
1) Will it have the Chip SAK-TC399XE-256F300S BD, mounted on it? OR
2) What chip (give me full name) , will be mounted in it so i can search its full capacity..?
大家好 :
关于ADC和DMA 有几个疑问,想得到帮助。
1.官方例程TLE9879_DMA_ADC1中,adc_ch_result[DMA_CH0_NoOfTrans]数组设置为8,但是IFXCONFIG里面,图1所示序列模式勾选了14个(7个通道+7个通道4重复采集),那么这个地方,DMA在传数的时候,是不是把前几个就给覆盖了?
2.DMA配置里,ADC1->RES_OUT7.reg这个配置是干嘛用的?
3.DMA完成中断触发条件是什么,是完成一个通道还是完成整个一次多通道扫描?
4.采集的数为什么设置为32位的,ADC是12位的。
5.如果我想测量2通道的ADC的数,一个P2.4的电压+一个VDH的电压,循环扫描,实时更新,该怎么配置。
因为资料较少,看了半天文档也是不明所以,希望得到解答。
Show Less
Hello all,
I am able to see UCB_PLFASH register on my TC38x.
But UCB_DFLASH I am unable to see. Initially I was able to see and modify also with Trace32.
Can anyone suggest what to do?
PFA image for reference w.r.t current situation.
Thanks in advanced.
Show Less
When i porting stm32h745 + Laird(lwb+), but stoped install firmware.
I think bluetooth sensor can't init hello_sensor_application_init();
But nucleo-745zi-q + Lwb(4343w) it's worked.
Show Less
I would like to ask what would cause this error?
What I have in my code is to create an array of outputs on the INT side of EP0 in the UART callback function, and then push the data from inside the UART out through the IN side of EP0. Now this build output array reports an error
Serial DEbug Reply:
What's going on here? Anyone know?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/USB%E4%B8%BB%E6%9C%BA%E9%9B%86%E7%BA%BF%E5%99%A8%E6%94%B6%E5%8F%91%E5%99%A8/USB%E8%BD%AF%E4%BB%B6%E9%85%8D%E7%BD%AE%E9%97%AE%E9%A2%98/td-p/724545
Show LessHello.
Regarding 3DL After entering deepsleep, the MCU current is around 4mA when measured separately. Both cores executed Cy_SysPm_DeepSleep to confirm that the MCU entered DeepSleep. what could the high current be related to?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/TRAVEO-T2G/3DL-deepsleep-%E7%94%B5%E6%B5%81/td-p/724510
Show LessHello, I've recently been learning how to extract respiratory heart rate signals with BGT60TR13C radar with Python. How can I convert the recorded data to the data required for FFT?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E9%9B%B7%E8%BE%BE%E4%BC%A0%E6%84%9F%E5%99%A8/How-to-use-BGT60TR3C-to-extract-respiratory-heart-rate-signals-in-Python/td-p/724498
Show LessI am new to the PowIR Build tool, I need to understand how to set the output voltage for IRPS5401, I have done required configuration based on my requirement when I create a new device and I have all input voltages, output voltages, etc. for SWA, SWB, SWC, SWD, LDO I have created a pcd file, but I want desired output to be written into the register not into the OTP .
Before writing/testing with config file I want to understand the tool, with default values when i2c is detected how to write value into the register and read.
If someone could point me the procedure of writing into the register it would be helpful for me to understand the tool by providing any source code or detailed pdf (Guide)
Thanks & Regards
Muvva Navin Krishna
Show Less