Featured Discussions
Hello, We have FS100R12W2T7 module in use, but the module Datasheet doesn't have SC data labeled TC=25C, can I simply calculate the short circuit current for TC=25C based on the trend of 175C-150C?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/IGBT-Datasheet-SC-data/td-p/716531
Show LessI reconfigure the firmware in config.h: I just modify the bandwidth into 0MHz ,I try to transmit signle tone with my board.
And I also flash the new .hex file inro my board successfully with XMC Flasher.
When I reconnect my board with new FW into my PC, it's LED just like this, only one yellow LED lighting
And when I open GUI, it show no Device connected, and my matlab code also can't run:
Then how can I know this radar still work and really the bandwidth is 0MHz. And if it's still working, I want to extraxt raw data with my matlab code? How can I modify the original code? I really need help, thanks!
Show Less
Hello Team,
I walk through the TC375XX tricore infineon Micro safety manual, I see lot of internal and external software and hardware safety mechanisms.
My understanding is that the Internal and external safety mechanisms would be implemented and prevented against the safety Goal. I would like to know what the MCU safety Goal are or is there any Assumptions of use case considered? please clarify.
Regards,
Nallusamy
Thanks for anyone who access my problem. How can Mulitcore access same variable in the same time When using Tricore TC389 with Hightec IDE?
I had put memset() in core0,core1,core2,core3's while(1), to set an large array to diffrent content. There is nothing error or unexcept happen. I just can see the var jump between different number, Dose infineon did some basework in tricore? Is this a safety way to access variables in multicore ?
Do you have any manual to explane this questions? Please give me a demo that show how to access variables in multicore in safety way.
Show LessHello,
I am developing a program that executes the XMC Flasher .exe, and programs a board using said flasher.
However, I would like to be able to program/set BMI of multiple boards at the same time by having multiple programmers connected into my PC. If multiple XMC programmers are connected to my PC at once, is there a way to identify, select, and control a specific programmer, perhaps through the programmer's COM port or serial number?
If not possible through XMC Flasher, is there is other software that would accomplish what I'm trying to do?
Thank you,
Alex
Show Less
1.TLE9879 _Evalkit_v1.4 What are the main functions of swdio R46 and swclk R50 and how are these values selected?
2.tle987x series power up swd part power up timing have a detailed explanation?
--------
Infineon-Z8F80032532_HW_Design_Guideline-ApplicationNotes
-----
Infineon-BLDC_shield-UserManual-v01_02-EN
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/MOTIX-MCU/SWD/td-p/716438
Show LessHello, I would like to know what are TSN standards does the Aurix TC399 microcontroller supports?
Hello,
I am currently trying to use the ASCLIN module as UART in the KIT_A2G_TC399_5V_TRB development kit, but having problems with TX. The examples I have found always use interrupts, which I do not want to use. I want to transmit data via polling instead.
I was able to receive data, but not sending anything. I have monitored the TX pin with an oscilloscope, and it remains always in VDD level.
Currently, I am using the following steps to initialize the ASCLIN module and to send data:
Initialization steps:
1) Reset EndInit
2) Enable the module via CLC.DISR
3) Set EndInit
4) Disable the clock via CSR.CLKSEL
5) Set INIT Mode in FRAMECON.MODE
6) Flush TXFIFO via TXFIFOCON.FLUSH
7) Set TXFIFOCON.INW=1 and TXFIFOCON.ENO=1
8 ) Flush RXFIFO via RXFIFOCON.FLUSH
9) Set RXFIFOCON.INW=1 and RXFIFOCON.ENO=1
10) Configure BITCON, DATCON, BRG and FRAMECON with desired baudrate and data bits parameters
11) Set ASC Mode in FRAMECON.MODE
12) Disable all flags in FLAGSENABLE
13) Clear all flags in FLAGSCLEAR
14) Configure the pins (Rx as input, Tx as output - pushpull and function 2)
Send data steps:
1) Wait for TXFIFOCON.FILL = 0
2) Copy data to send via TXDATA = data
Is there anything else needed to enable TX?
Thank you in advance,
Alisson Furlani
Show Less