- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Not really a component per se, but after receiving multiple requests from all you awesome viewers, I decided I needed to get it out to the world SOMEHOW so I decided why not here on this forum. It technically does include my modified DeltaSigma modulator with the "mod" input... : )
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Many thanks for publishing this example
Viktor
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
For fun, here are the related videos:
Part 1: http://www.youtube.com/watch?v=w78aO8j4olg
Part 2:http://www.youtube.com/watch?v=BgyQuCZP2jU
Part 3: http://www.youtube.com/watch?v=wWeBnhW2YEo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Just a note for making this work with Creator 3.1 for PSoC 5LP.
Add the linker flag -u _printf_float by going to Project -> Build Settings -> Linker -> Command line. This will add floating point support for sprintf.
You will also need to increase the heap size in the .cydwr file under the Systems tab. A size ov 0x0800 should be fine. This gives the sprintf function room to work.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Any updates for PSOC 5 and Creator 3.3?. I am getting a lot of errors (after updating components...)
Thank you and best regards..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I Just downloaded the project, expanded it, updated all components and compiled it successfully using Creator 3.3 CP1.
Then I changed the device to CY8C5888AXQ-LP096 and again no errors when re-built.
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Bob;
Re-downloaded the project, updated components, the project builds successfully in the original form, now it also builds OK using a PSOC 5. I am using the same chip you selected. The errors I had before are not there anymore, so I guess my project files were corrupted.
Best regards,
kreutz
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please kees ,
i dont know how to connect the hardware wires. in the schematic there are 4 TP , i suppose that unknown impedance will be connected to P01 and P05 (Drive_out and TIA_input) but for Drive_sense and TIA_Sense where should i connect these ??
thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Did you by any chance figure out the connection issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Kees and Cypress community,
i am a student. i had followed exactly the way Kees test the impedance meter project, however when i insert any component there to test the impedance meter, `CLIPPING` error always happened and no result are displayed. what should i do to overcome this problem?
thanks for your concerned
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Did you by any change figure what's causing the "CLIPPING" error?