- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
On my boards I have found that if the bootloader is running (USB boot selected PMODE=F11), some GPIO pins are driven avtively. As an example, GPIO[51] is driven low by the FX3. If the FX3 is hold in reset, the GPIOs seem to be in high impedance state. There are also other GPIOs affected, but GPIO[51] is the one I was investigating since it is important for us that this pin is high impedance state.
I have found this behaviour of GPIO[51] on our custom hardware with the CYUSB3014 production code 1149 and the Cypress Rev 2 DVK Kit having production code 1113. Has somebody else also observed such behaviour?
At this point I would like to get a statement from Cypress, how the bootloader is initialising the GPIOs. As you guys have access to the bootloader code, it should be easy enough to tell us. Thanks.
Regards
Silvio
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Silvio,
As it is related to bootloader it would be a good idea to discuss this over a tech support case. Please create a tech support case (MyAccount -> MyCases) so that we can take a deeper look into this.
Regards,
Anand
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Is there any update on this issue. GPIO50 and 57 also seem to be actively driven. Could Cypress let us know the default states of all the GPIO. They do not all default as inputs and this will cause problems if their initial state is not known
Sodafarl
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have still an open webcase on this. So far Cypress admitted that they were able to repeat the reported behaviour on GPIO[51] but apparently not all boards tested behaved the same.
My feeling was already before that more pins than GPIO[51] are affected and now Sodafarl is finding the same. I think Cypress needs to clarify this asap.
-Silvio
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I'll follow-up with our team and provide an update on this as soon as possible.
Regards,
Anand
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
In the meantime I got the following information. GPIO[0..32] are still missing though.
GPIO# | Pin State |
33 | Tri-state |
34 | Tri-state |
35 | Tri-state |
36 | Tri-state |
37 | Tri-state |
38 | Tri-state |
39 | Tri-state |
40 | Tri-state |
41 | Tri-state |
42 | Low |
43 | Tri-state |
44 | Tri-state |
45 | High |
|
|
46 | Tri-state |
47 | Tri-state |
48 | Tri-state |
49 | Tri-state |
50 | Tri-state |
51 | Low |
52 | Tri-state |
53 | High |
54 | Tri-state |
55 | High |
56 | Tri-state |
57 | Tri-state |
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Silvio,
Saw the case. Was just about to post it.
Thanks for posting it here.
Regards,
Anand
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Our experience on the rev 3 DVK has been that the bootloader won't enumerate over USB if any of the following are being driven during boot:
GPIO[0] - GPIO[8]
GPIO[10]-GPIO[15]
GPIO[18]-GPIO[19]
GPIO[29]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Has there been any official word from Cypress on this issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
GPIO # 33 to 57 are same as Silvio posted above ( Sil posted on 09 May 2012 11:05 PM PST ).
GPIO # 0 to 29 are in "Tri-state".
GPIO # 30 to 32 are "inputs to the FX3".
Thanks,
sai krishna.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
To force a GPIO to tri-state, please use the API as follows:
CyU3PGpioSetIoMode(GPIO_NUMBER,0);
-Madhu
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I've got a question regarding the Knowledge Base article "FX3 GPIO Pin Condition During Reset - KBA86731" (http://www.cypress.com/?id=4&rID=91267):
The document defines the default GPIO states for "USB Boot mode". What about the "SPI Boot mode"? Do the same default GPIO states apply for this boot mode?
Regards,
Stefan
===============================================================================================
2015-03-05 Update:
Hello,
meanwhile I found the information I'd looked for in the AN76405 "FX3 Boot Options" (see Table #29):
http://www.cypress.com/?docID=49862
Regards,
Stefan