- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello community, I am a PSoC beginner and want to start with the PSoc Creator 4.0 software. So I installed PSoC Creator 4.0 Update 1 (typical) on the 4th PC. OS: Win 10 home. (German) Processor: I5-7200 RAM: 4 GB SSD The software I have registered, checked "i'd like to help ..." and Level 3 . Then I created a new project. Under Target Device, I have selected PSoC 4200 because I want to use the CY8CKIT-049-42xx. After that, I chose an empty schematic and waited until the project was created. Then I drag 'n drop an AND gate on the emty schematic. After this I only moved the gate and the software freezes and reported " no response" in the title bar. After 15 seconds the software was operable again. I come to the conclusion that the software does not work properly on four PCs now. It is a pity because I would have liked to know the functionalities of the PSoCs. After 3 weeks trying and serching for solutions it is (on four different PCs) not possible to work with PSoC Creator 4.0 ?!? Someone has an idea what could be the cause? For me it is not comprehensible! Many thanks in advance best regards Andreas
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Can you try the steps as shown in the attached document and see if it makes any difference.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Welcome in the forum, Andreas.
Are you using network drives on your PCs?
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Excuse me,Do you have a program package for CYBLE 212006-01?
HI,Bob Recently I was learning CY8CKIT-042-BLE debugging,The Bluetooth module is cyble 212006-01,However, there is no official website on the cypress program development package,I found out that you've been working on this for a long time,So I would like to ask if you have this program development kit- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I was not asking for a network connection but for using a network drive share. With every move of a component several files get accessed which usually is no problem. When any of the files reside on a network share which cannot be accessed/searched there is a timeout for that try.
When this situation is not the case I would suggest to contact Cypress directly (might take some time because of Eastern holidays): At top of this page click on "Design Support -> Support -> Create a Support Case".
Bob
PS: Where in Germany are you located? I live near Bremen,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Too bad. I run Creator flawlessly on several different machines. Something must be special to your installations, as a common driver or something else. Did you already try running Creator with admin rights? Have you got any language specific characters (äöüß) in your path names or username?
Check actual version of your dot net environment.
Bob
PS I lived 4 years in Köln Flittard (Bayer Leverkusen)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content