- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I am trying to adquire EMG signal with CY8CKIT-044, does someone make something about that with this module?
Thank you a lot!
Regards.
Solved! Go to Solution.
- Labels:
-
ispn:39614:1:0
-
l1:314:1:0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
These are mainly discussions for PSoC5LP, you will have to adapt them for CY8CKIT-044.
Have you searched the forum? eg:
https://community.cypress.com/search.jspa?q=EMG
or ECG.
one of the discussions: PSOC5 ECG UNSTABILITY
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
What do you want to know in this thread?
Please post the details.
Regards,
Kenshow
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Kenshow,
Thank you for your response,
I´m trying to adquire EMG signal in differential mode using 3 OPAMPs before SAR. Is this method correct? Is there any way to adquire more than 1 channel?
Another thing, where can I put the reference? I thought put the reference in the Injection channel of SAR but I don´t know how to control the baseline in firmware.
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The EMG signal seems to have a range of about -5 to +5 mV.
Those. this is ~ 5 times the ECG signal.
They have similar concomitant problems and interferences.
Yes, you can use 3 OPAMPs before SAR.
considering that amplifiers should have a small offset (> + 300mV)
This forum has several topics about ECG.
perhaps it makes sense to use specialized microcircuits (Ad8232) boards for EMG and ECG.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Evgeniy,
thank you for your response. As you said, EMG and ECG have a quite similar adquisition circuit but there are some differences, for example, the reference circuit, I couldn´t find anythin in this forum about that, do you know something about it?
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
These are mainly discussions for PSoC5LP, you will have to adapt them for CY8CKIT-044.
Have you searched the forum? eg:
https://community.cypress.com/search.jspa?q=EMG
or ECG.
one of the discussions: PSOC5 ECG UNSTABILITY
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you, I will take a look in both links you have shared. Is it possible to use the PSoC 5LP integrated in CY8CKIT-044 to use its components within the same project that I designed with PSoC 4?
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I don't have CY8CKIT-044 so I don't know the answer.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OsFe,
No. To use PSoC5 integrated into KIT-044, it has to be programmed in a separate project. Though some people do that, in my opinion it is not worth the hassle. Since PSoC5 is used as a programmer, you have to reprogram back-and-force each time PSoC4 project needs to be updated. If PSoC4 resources are not enough, I would recommend $10 cy8ckit-059 PSoC5 prototyping board, or, in case of opamps, use external ones.
Another low budget approach is to utilize low-cost 24-bit Delta Sigma ADC HX711, operating at 80Hz.
HX711: 24-bit Delta Sigma ADC interface for weight scale using PSoC
which has built-in opamp
/odissey1