- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
it is possible update CYPD3175-24LQXQ FW via TYPE C connector ?
Q: if yes what type of project need to be prepare ?
no boot project ?
bootable project ?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
Q1 : it is poosible update FW CVPD3175 without power board via Type port C ? if yes please send instruction
>> No. Power board is the key.
Q2 : what is correct setup of jumpers on power board and main board while using it to update FW CYPD3175
>> Refer below "PRG".
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
CYPD3175-24LQXQ example firmware in SDK is supporting CC bootloader by default. It is can be upgrade by Type-C host, for example, CCG4, to upgrade firmware via CC line of Type-C interface.
It is should be bootloader project.
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
It is possible to upgrade CCG3PA firmware by CY4532 power board.
You need make sure you have below items on your hands:
1. Ez-PD configuration Utility (https://www.cypress.com/documentation/software-and-drivers/ez-pd-configuration-utility ) installed in your notebook/PC.
2. A Type-C to Type-C cable (recommend use university Type-C cable on market). This is for connect CY4531 Type-C interface to the CCG3PA's Type-C interface you are going to upgrade.
3. A Type-A to mini-B cable. This is for connect CY4531 Type-C interface to the notebook/PC which is installed Ez-PD configuration Utility.
4. The CCG3PA board shall be powered.
The details guidance could find out in the user guide: https://www.cypress.com/file/372576/download , Section 4.1 Programming the CCG3PA Controller on the CY4532 EVK.
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Lisa
i want understand more accuretly how update FW CYPD3175
Q1 : it is poosible update FW CVPD3175 without power board via Type port C ? if yes please send instruction
Q2 : what is correct setup of jumpers on power board and main board while using it to update FW CYPD3175
i have been read all steps 1-4 in your earlier message but unfortunately the EZ-PD™ Configuration Utility does not recognize any device
i tried to setups
two options was tried either both of them not working
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi ,
Q1 : it is poosible update FW CVPD3175 without power board via Type port C ? if yes please send instruction
>> No. Power board is the key.
Q2 : what is correct setup of jumpers on power board and main board while using it to update FW CYPD3175
>> Refer below "PRG".
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
ok thanks do we need EMCA cable connect between power board and CYPD3175 ?
where i can purchase it ?
i saw in https://www.cypress.com/documentation/development-kitsboards/cy4501-ccg1-development-kit
CCG1 Electronically Marked Cable Assembly (EMCA) board
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Type-C to Type-C cable is enough. Do not need EMCA cable.
Best Regards,
Lisa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
:1. see attached image file setup.png
2. see attached image file screenshot of ez pdc configuration utility ( not recognize cypd3175 device )
Q: what application on PC do we need use in order update fw via cc line does ez pd configuration utility fit ?
Q on power board what is the correct setup of jumpers in earlier answer you mention only main board
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
If the last questions are open, please create a new discussion.