- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
I have a TypeYDt Murata module.
'console' the sample code has been tested.
But not if the ping test.
I have tested with the same procedure below.
step 1. join samwoo_R&D wep key 192.168.0.57 55.255.255.0 192.168.01
Joining : samwoo_R&D
successfully joined : samwoo_R&D
Setting IPv6 link-local address
IPv4 network ready IP : 192.168.0.57
step 2. ping 192.168.0.1
Ping timeout
ping 192.168.0.58
Ping timeout
step 3. status
WICED Version : 3.1.2
Platform : MurataTypeYD
MAC Address : 90:B6:86:98:41:2D
STA Interface
MAC Address : 90:B6:86:98:41:2D
SSID : samwoo_R&D
IP Addr : 192.168.0.57
Gateway : 192.168.0.1
Netmask : 255.255.255.0
AP Interface : Down
P2P Interface : Down
step 4. Wifi connection in the module and confirmed that AP.
step 5. This ping should not be on the PC. ( ping 192.168.0.57 )
Why should not what ping?
I would like to know what went wrong.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
'console' sample is provided by broadcom.
So I think that the questions are right here.
What can not be supported against the sample code provided in the broadcom?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hey,
So, I checked the steps that you mentioned with BCM943362 and WICED SDK 3.4.0
Step 1: Join the Access Point
Step 2: Check the IP of my machine : 10.16.96.105
Step 3: Ping my Machine using 10.16.96.105
Step 4: Status
Can you try with the WICED 3.4.0 SDK?
Hope that helps
Best Regards,
AB
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
Thank you for having answers.
I was having trouble connecting Come to the test again.
Connection security schemes open, wpa-psk, wpa2-psk this is connected to the well.
But wep approach seems the connection is not good.
Why should not what wep way connection?
command : join samwoo wep ff11dd22cc
do not get the ip assigned.
I am that we have ap, ip router each test.
SDK Version 3.1.2
Please advice me.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Jinho,
I've noticed you are using an older version of the SDK. Could you please try again with the newest 3.4.0 SDK and let us know if you are still seeing the same issue? You can download it at the below link. Thanks!
WICED SDK supporting Amazon Web Services 3.4.0-AWS
Regards,
Jaeyoung
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hey,
I tried the application with wep.
It does work on BCM943362 and WICED SDK 3.4.0.
I would suggest using the WICED SDK 3.4.0.
Let us know if that worked.
Best Regards,
AB