- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I am using CYW920719Q40EVB-01 board to test different code. First, i wanted to try SPP code to download and see the communication using any SPP app( i have downloaded "SPP" app) but not able to establish the set up and debug the code to see its functionality.
I referred to pdf " CYW920719Q40EVB-01 JTAG DEBUGGING", but i am getting one error, i am attaching the screenshot of that error.
Please help me how to proceed it.
Thanks & Regards,
Ekta
Solved! Go to Solution.
- Tags:
- cyw920719q40evb-01
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Updated steps:
Filename: spar_utils.h
------------------------------
1) Modify the debugging enable macros as shown below. (Or copy the below code and comment out the original macro definition)
NOTE: If you are using some other pin as SWDCK and SWDIO (other than P33 and P34), you will have to wire up the debug hardware accordingly to the EVAL kit.
#include "gpiofunction.h"
void _tx_v7m_set_int(unsigned int posture);
unsigned int _tx_v7m_get_int(void);
#ifdef DEBUG
/// When debugging is enabled, sets up the HW for debugging.
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED() do{ \
wiced_hal_gpio_select_function(WICED_P33, WICED_SWDCK); \
wiced_hal_gpio_select_function(WICED_P34, WICED_SWDIO); \
wiced_hal_wdog_disable(); \
}while(0)
/// Optionally waits in a pseudo while(1) until the user allows the CPU to continue
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED() do{ \
volatile UINT8 spar_debug_continue = 0; \
unsigned int interrupt_save = _tx_v7m_get_int();\
while(!spar_debug_continue); \
spar_debug_continue = 0; \
_tx_v7m_set_int(interrupt_save); \
}while(0)
#else
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED()
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED()
#endif
Filename: gpiofunction.h
---------------------------------
1) Replace #include "gpiodriver.h" with #include "wiced_hal_gpio.h".
//#include "gpiodriver.h"
#include "wiced_hal_gpio.h"
2) Remove/comment out below code.
//typedef enum GPIO_STATUS_e
//{
// GPIO_FAILURE,
// GPIO_SUCCESS,
// GPIO_REMAPPED,
// GPIO_MOVED
//} GPIO_status_t;
3) Replace all gpio_numbers_t with wiced_bt_gpio_numbers_t.
4) Replace GPIO_status_t with wiced_bt_gpio_select_status_t.
Filename: spp.c
----------------------
1) Add below macros in APPLICATION_START()
SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED();
BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED();
2) #include "spar_utils.h"
Filename: makefile.mk
------------------------------
1) add below flag.
C_FLAGS+= -DDEBUG
Filename: maketarget string (when downloading)
------------------------------------------------------------------
In the Eclipse “Make target”, ensure DEBUG=1 is on the command line.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ekta,
Can you please try the steps mentioned in the following thread: Cypress CYW920719Q40-B1 eval kit debugging
Thanks,
Anjana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The issue is GDB server and client are not initiating connection properly. Please go through the below workarounds. And also check whether you have made all the changes what I listed below.
->Workaround_1:
Open a SEGGER J-link GDB Server and establish connect to the target, and, KEEP IT OPEN. Then start a debugging session from WICED as usual.
->Workaround_2:
Go to Debug Configurations in WICED and select Debugger tab.
In GDB Client Setup Select arm-none-eabi-gdb.exe for Executable from C:\Users\username\Documents\WICED-Studio-6.4.0.61\43xxx_Wi-Fi\tools\ARM_GNU\Win32\bin\arm-none-eabi-gdb.exe. Then start a debugging session from WICED as usual.
Below are the changes what I have done to start a debugging session using WICED. Please check whether you have done all the below changes properly.
Filename: spar_utils.h
------------------------------
1) Modify the debugging enable macros as shown below. (Or copy the below code and comment out the original macro definition)
NOTE: If you are using some other pin as SWDCK and SWDIO (other than P33 and P34), you will have to wire up the debug hardware accordingly to the EVAL kit.
#include "gpiofunction.h"
void _tx_v7m_set_int(unsigned int posture);
unsigned int _tx_v7m_get_int(void);
#ifdef DEBUG
/// When debugging is enabled, sets up the HW for debugging.
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED() do{ \
wiced_hal_gpio_select_function(WICED_P33, WICED_SWDCK); \
wiced_hal_gpio_select_function(WICED_P34, WICED_SWDIO); \
wiced_hal_wdog_disable(); \
}while(0)
/// Optionally waits in a pseudo while(1) until the user allows the CPU to continue
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED() do{ \
volatile UINT8 spar_debug_continue = 0; \
unsigned int interrupt_save = _tx_v7m_get_int();\
while(!spar_debug_continue); \
spar_debug_continue = 0; \
_tx_v7m_set_int(interrupt_save); \
}while(0)
#else
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED()
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED()
#endif
Filename: gpiofunction.h
---------------------------------
1) Replace #include "gpiodriver.h" with #include "wiced_hal_gpio.h".
//#include "gpiodriver.h"
#include "wiced_hal_gpio.h"
2) Remove/comment out below code.
//typedef enum GPIO_STATUS_e
//{
// GPIO_FAILURE,
// GPIO_SUCCESS,
// GPIO_REMAPPED,
// GPIO_MOVED
//} GPIO_status_t;
3) Replace all gpio_numbers_t with wiced_bt_gpio_numbers_t.
4) Replace GPIO_status_t with wiced_bt_gpio_select_status_t.
Filename: spp.c
----------------------
1) Add below macros in APPLICATION_START()
SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED();
BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED();
Filename: makefile.mk
------------------------------
1) add below flag.
C_FLAGS+= -DDEBUG
Filename: maketarget string (when downloading)
------------------------------------------------------------------
In the Eclipse “Make target”, ensure DEBUG=1 is on the command line.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Updated steps:
Filename: spar_utils.h
------------------------------
1) Modify the debugging enable macros as shown below. (Or copy the below code and comment out the original macro definition)
NOTE: If you are using some other pin as SWDCK and SWDIO (other than P33 and P34), you will have to wire up the debug hardware accordingly to the EVAL kit.
#include "gpiofunction.h"
void _tx_v7m_set_int(unsigned int posture);
unsigned int _tx_v7m_get_int(void);
#ifdef DEBUG
/// When debugging is enabled, sets up the HW for debugging.
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED() do{ \
wiced_hal_gpio_select_function(WICED_P33, WICED_SWDCK); \
wiced_hal_gpio_select_function(WICED_P34, WICED_SWDIO); \
wiced_hal_wdog_disable(); \
}while(0)
/// Optionally waits in a pseudo while(1) until the user allows the CPU to continue
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED() do{ \
volatile UINT8 spar_debug_continue = 0; \
unsigned int interrupt_save = _tx_v7m_get_int();\
while(!spar_debug_continue); \
spar_debug_continue = 0; \
_tx_v7m_set_int(interrupt_save); \
}while(0)
#else
#define SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED()
#define BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED()
#endif
Filename: gpiofunction.h
---------------------------------
1) Replace #include "gpiodriver.h" with #include "wiced_hal_gpio.h".
//#include "gpiodriver.h"
#include "wiced_hal_gpio.h"
2) Remove/comment out below code.
//typedef enum GPIO_STATUS_e
//{
// GPIO_FAILURE,
// GPIO_SUCCESS,
// GPIO_REMAPPED,
// GPIO_MOVED
//} GPIO_status_t;
3) Replace all gpio_numbers_t with wiced_bt_gpio_numbers_t.
4) Replace GPIO_status_t with wiced_bt_gpio_select_status_t.
Filename: spp.c
----------------------
1) Add below macros in APPLICATION_START()
SETUP_APP_FOR_DEBUG_IF_DEBUG_ENABLED();
BUSY_WAIT_TILL_MANUAL_CONTINUE_IF_DEBUG_ENABLED();
2) #include "spar_utils.h"
Filename: makefile.mk
------------------------------
1) add below flag.
C_FLAGS+= -DDEBUG
Filename: maketarget string (when downloading)
------------------------------------------------------------------
In the Eclipse “Make target”, ensure DEBUG=1 is on the command line.