- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I am using Murata WLAN Combo Module SP-HY1MW-F chip which has BCM43455 inside it.
I am using Broadcom generic fmac driver. The firmware & nvram is downloaded from https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/brcm.
I am struggling to enable Wifi AP & STA mode at a time:
1) When I use connmanctl tether command, it disables the client mode & enables the AP mode, but not both at a time.
2) When I try creating new interface of managed mode for tethering, it throws an error: Not supported (-95)
3) When I try creating bridge manually using ip commnd & connecting wlan0 with bridge as a master, it also throws me the error: Not supported (-95)
Can you please help me with the issue?
Thanks & Regards,
Brinda Pathak
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
Go through the attached document for see if this helps in setting up APSTA.
We are using clients of hostapd and wpa_supplicant for setting up AP and sta respectively. Could you check whether you are creating the Ap in the virtual interface that is created(wlan1 in the document). Try setting up the STA in the primary interface and AP in the virtual interface and see if it passes.
Regards,
Vinayak
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi
Go through the attached document for see if this helps in setting up APSTA.
We are using clients of hostapd and wpa_supplicant for setting up AP and sta respectively. Could you check whether you are creating the Ap in the virtual interface that is created(wlan1 in the document). Try setting up the STA in the primary interface and AP in the virtual interface and see if it passes.
Regards,
Vinayak
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks a lot Vinayak for the detailed explaination.
I am still getting the below error on ./hostapd /etc/hostapd.conf -B command.
[ 136.380603] brcmf_link_down: WLC_DISASSOC failed (-11)
[ 136.568104] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
wlan1: interface state UNINITIALIZED->ENABLED
wlan1: AP-ENABLED
[ 137.040578] brcmf_sdio_hostmail: Unknown mailbox data content: 0x40012
[ 139.520212] brcmf_sdio_bus_rxctl: resumed on timeout
[ 142.080204] brcmf_sdio_bus_rxctl: resumed on timeout
[ 142.085258] brcmf_c_set_joinpref_default: Set join_pref error (-110)
[ 144.640211] brcmf_sdio_bus_rxctl: resumed on timeout
[ 147.200253] brcmf_sdio_bus_rxctl: resumed on timeout
[ 147.205307] brcmf_cfg80211_connect: BRCMF_C_SET_SSID failed (-110)
n[ 149.840214] brcmf_sdio_bus_rxctl: resumed on timeout
[ 149.845264] brcmf_do_escan: error (-110)
[ 149.849223] brcmf_cfg80211_scan: scan error (-110)
[ 152.400225] brcmf_sdio_bus_rxctl: resumed on timeout
[ 152.405670] _brcmf_set_multicast_list: Setting mcast_list failed, -110
[ 154.960263] brcmf_sdio_bus_rxctl: resumed on timeout
[ 154.965736] brcmf_do_escan: error (-110)
[ 154.969705] brcmf_cfg80211_scan: scan error (-110)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Could you try using the firmware that is present in the latest manda release present in the community.
BR
-Vinayak