- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Im not able run and debug programs in EZ-USB FX3 development kit. how to launch?
please suggest
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Pooja,
Using eclipse to build the project is not mandatory. You can invoke the make file using command prompt.
I think your problem would be as below:
After building even though there is a make error shown in eclipse please check the debug folder and look for .elf file. If the elf file is generated then the project is already built.
Then to convert the elf file to .img file(which is used for programming fx3) you can make use of elf2img.exe utility which is included in the utils folder of fx3 sdk.
Regards,
Hemanth
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
- You can program the firmware built using the ezUsbSuite into the RAM/EEPROM on the CYUSB3KIT-003 and test the functionality. Alternatively, you can use the JTAG based debugging of firmware using the on-board USB-Serial JTAG debugger. Please refer to section 3 of EzUsbSuite.PDF document for details on JTAG debugging.
Best regards,
Srinath S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pooja,
- Please let me know if you are inquiring about running the ezUsbSuite.exe file or the firmware (.img file) compiled using the ezUsbSuite.
Best regards,
Srinath S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Sir,
EZusbsuite.exe files
Another doubt is im getting some errors in example programs like
cs-make: *** Error (BootLedBlink)
so how should I resolve it ??
Is there any video link for how to debug and run example programs because I’m not able debug and run and even blue LED is not turned ON as im connecting it to USB 2.0 , but Kit gets turned ON .
Does the default program from EEPROM of kit gets deleted ???
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Pooja,
- Please view the below image to execute the ezUsbSuite.exe file from the directory.
- Perform a 'Clean Project' operation on the project and then build the same. Do let me know if the error still persists.
- Use the Cypress USB Control Center application to check if the device is detected on the host PC.
- Kindly, use the attached firmware project and check if there is a blink on the LED (if connected to SuperSpeed USB port) or if the LED turns ON (if connected to High Speed USB port).
Best regards,
Srinath S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sir when I’m performing this Boot From Onboard I2C EEPROM
Blue Led2 does not glow as I’m connecting it with USB2.0 and when I transfer data in Control Center I’m getting
CONTROL OUT transfer
CONTROL OUT transfer failed with Error Code:997
Sir even Im not able add the example programs in workspace I mean im getting the red cross marks for example programs
How to resolve its please suggets
I tried with Command Prompt its showing the system cannot find specified path, so tried to set path but not able to do.
The blue LED (LED2) is connected to GPIO54(SPI-SSN) of FX3. The LED glows when GPIO is driven low .
So how to get the GPIO pin low??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Please download latest EZ-USB FX3 SDK 1.3.4. Use the examples provided in the same for getting started with the Explorer kit. Try building the firmware in the following path: "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\firmware\basic_examples\cyfxbulksrcsink" and test the same.
Regards,
Hemanth
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Pooja,
Using eclipse to build the project is not mandatory. You can invoke the make file using command prompt.
I think your problem would be as below:
After building even though there is a make error shown in eclipse please check the debug folder and look for .elf file. If the elf file is generated then the project is already built.
Then to convert the elf file to .img file(which is used for programming fx3) you can make use of elf2img.exe utility which is included in the utils folder of fx3 sdk.
Regards,
Hemanth