- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I followed the CYUSB3KIT-003 SuperSpeed Explorer Kit User Guide perfectly. I runned the USBBulkSourceSinkLED and was able to see messages on UART, use the JTAG debugger and modifiy the code. However, I want to generate the the img file. I deleted the img files on both the workspace and the original place of the source code to make sure if any img file appears it will be the newly created one.
I followed both: Generate Bootable Image File for FX3 with I2C EEPROM - KBA218344 and FX3 EZ USB Suite cannot generate image file. In the end I even put the exact path like the following picture shows:
When I try to compile I get:
```
14:24:20 **** Incremental Build of configuration Debug for project USBBulkSourceSinkLED ****
cs-make all
Building target: USBBulkSourceSinkLED.elf
Invoking: ARM Sourcery Windows GCC C Linker
arm-none-eabi-gcc ./cyfx_gcc_startup.o ./cyfxbulkdscr.o ./cyfxbulksrcsink.o ./cyfxtx.o -T"C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\/firmware/common/fx3.ld" -nostartfiles -Wl,-Map,USBBulkSourceSinkLED.map -Wl,-d -Wl,--no-wchar-size-warning -Wl,--gc-sections -Wl,--entry,CyU3PFirmwareEntry "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyfxapi.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyu3lpp.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyu3threadx.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\ARM GCC\\arm-none-eabi\lib\libc.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\ARM GCC\\lib\gcc\arm-none-eabi\4.8.1\libgcc.a" -mcpu=arm926ej-s -mthumb-interwork -g -gdwarf-2 -o"USBBulkSourceSinkLED.elf"
Finished building target: USBBulkSourceSinkLED.elf
C:/Program Files (x86)/Cypress/EZ-USB FX3 SDK/1.3/ARM GCC/bin/cs-make --no-print-directory post-build
/usr/bin/sh: -c: line 0: syntax error near unexpected token `('
/usr/bin/sh: -c: line 0: `C:/Program Files (x86)/Cypress/EZ-USB FX3 SDK/1.3/ARM GCC/bin/cs-make --no-print-directory post-build'
cs-make: *** [USBBulkSourceSinkLED.elf] Error 1
14:24:22 Build Finished (took 1s.843ms)
```
So it seams the elf file is being created correctly. However I cannot seem to be able to generate the img file. Same problem with debug or release...
In the end I resigned to using only the elf version and programming the device via EZ-USB (eclipse) but when I hit run I get:
```
Error starting process.
Cannot run program "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED\Release\USBBulkSourceSinkLED.elf" (in directory "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED"): CreateProcess error=193, %1 is not a valid Win32 application
Cannot run program "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED\Release\USBBulkSourceSinkLED.elf" (in directory "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED"): CreateProcess error=193, %1 is not a valid Win32 application
Cannot run program "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED\Release\USBBulkSourceSinkLED.elf" (in directory "C:\Users\<MyUser>\Workspace\USBBulkSourceSinkLED"): CreateProcess error=193, %1 is not a valid Win32 application
```
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Hope this article will help you to solve the problem:
Fix “syntax error near unexpected token `('” in Eclipse IDE provided with FX3 SDK - KBA223154
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Could you please upload your whole project? I could check it for you on my side.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So here is the project in the Workspace folder. It should be the same as the downloaded in the path `C:\Program Files (x86)\Cypress\SuperSpeed Explorer Kit\1.0\Firmware\USBBulkSourceSinkLED`
I'm using OpenOCD following the instructions on the pfd attached.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Agustin,
I could build and generate Img file with your project. I do nothing and only try to build.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Here are the outputs from Console window.
10:09:28 **** Incremental Build of configuration Debug for project USBBulkSourceSinkLED ****
cs-make all
'Building file: ../cyfxbulksrcsink.c'
'Invoking: ARM Sourcery Windows GCC C Compiler'
arm-none-eabi-gcc -D__CYU3P_TX__=1 -I"C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc" -I"..\." -O0 -Wall -Wa,-adhlns="cyfxbulksrcsink.o.lst" -c -fmessage-length=0 -MMD -MP -MF"cyfxbulksrcsink.d" -MT"cyfxbulksrcsink.d" -mcpu=arm926ej-s -mthumb-interwork -g -gdwarf-2 -o "cyfxbulksrcsink.o" "../cyfxbulksrcsink.c"
../cyfxbulksrcsink.c: In function 'CyFxBulkSrcSinkApplnUSBSetupCB':
../cyfxbulksrcsink.c:429:30: warning: variable 'wLength' set but not used [-Wunused-but-set-variable]
uint16_t wValue, wIndex, wLength;
^
../cyfxbulksrcsink.c: In function 'CyFxBulkSrcSinkApplnInit':
../cyfxbulksrcsink.c:683:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_SS_DEVICE_DESCR, NULL, (uint8_t *)CyFxUSB30DeviceDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:691:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_HS_DEVICE_DESCR, NULL, (uint8_t *)CyFxUSB20DeviceDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:699:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_SS_BOS_DESCR, NULL, (uint8_t *)CyFxUSBBOSDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:707:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_DEVQUAL_DESCR, NULL, (uint8_t *)CyFxUSBDeviceQualDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:715:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_SS_CONFIG_DESCR, NULL, (uint8_t *)CyFxUSBSSConfigDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:723:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_HS_CONFIG_DESCR, NULL, (uint8_t *)CyFxUSBHSConfigDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
../cyfxbulksrcsink.c:731:5: warning: passing argument 2 of 'CyU3PUsbSetDesc' makes integer from pointer without a cast [enabled by default]
apiRetStatus = CyU3PUsbSetDesc(CY_U3P_USB_SET_FS_CONFIG_DESCR, NULL, (uint8_t *)CyFxUSBFSConfigDscr);
^
In file included from ../cyfxbulksrcsink.c:62:0:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\inc/cyu3usb.h:753:1: note: expected 'uint8_t' but argument is of type 'void *'
CyU3PUsbSetDesc (
^
'Finished building: ../cyfxbulksrcsink.c'
' '
'Building target: USBBulkSourceSinkLED.elf'
'Invoking: ARM Sourcery Windows GCC C Linker'
arm-none-eabi-gcc ./cyfx_gcc_startup.o ./cyfxbulkdscr.o ./cyfxbulksrcsink.o ./cyfxtx.o -T"C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\/firmware/common/fx3.ld" -nostartfiles -Wl,-Map,USBBulkSourceSinkLED.map -Wl,-d -Wl,--no-wchar-size-warning -Wl,--gc-sections -Wl,--entry,CyU3PFirmwareEntry "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyfxapi.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyu3lpp.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\\firmware\u3p_firmware\lib\fx3_debug\cyu3threadx.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\ARM GCC\\arm-none-eabi\lib\libc.a" "C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\ARM GCC\\lib\gcc\arm-none-eabi\4.8.1\libgcc.a" -mcpu=arm926ej-s -mthumb-interwork -g -gdwarf-2 -o"USBBulkSourceSinkLED.elf"
'Finished building target: USBBulkSourceSinkLED.elf'
' '
cs-make --no-print-directory post-build
'Converting ELF to image (.img) format'
"C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\util\elf2img\elf2img.exe" -i USBBulkSourceSinkLED.elf -o USBBulkSourceSinkLED.img
Note: 256 bytes of interrupt vector code have been removed from the image.
Use the "-vectorload yes" option to retain this code.
' '
'Invoking: ARM Sourcery Windows GNU Create Listing'
arm-none-eabi-objdump -h -S USBBulkSourceSinkLED.elf > "USBBulkSourceSinkLED.lst"
'Finished building: USBBulkSourceSinkLED.lst'
' '
'Invoking: ARM Sourcery Windows GNU Print Size'
arm-none-eabi-size --format=berkeley USBBulkSourceSinkLED.elf
text data bss dec hex filename
124232 692 6336 131260 200bc USBBulkSourceSinkLED.elf
'Finished building: USBBulkSourceSinkLED.siz'
' '
10:09:35 Build Finished (took 6s.986ms)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I copy pasted the .elf on the same folder the elf2img.exe is and I runned:
C:\Program Files (x86)\Cypress\EZ-USB FX3 SDK\1.3\util\elf2img>elf2img.exe -i USBBulkSourceSinkLED.elf -o USBBulkSourceSinkLED.img
Note: 256 bytes of interrupt vector code have been removed from the image.
Use the "-vectorload yes" option to retain this code.
So it seams to be working. Now I have to know just how to integrate it with EZ-USB. I'll come back when I solve it.
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Hope this article will help you to solve the problem:
Fix “syntax error near unexpected token `('” in Eclipse IDE provided with FX3 SDK - KBA223154
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OMG it worked. It's true I have the git in my envs and the fix did work.
Thank you a lot!!!