- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am unable to program PSoC 5lp. I could see both the LEDs(Red-target supply and Green- Status) are ON. When I acquire the port, I am getting "ARM DEBUG PORT"(Screen shot attached) INSTEAD OF PSoC 5lp. Kindly let me know how to determine what is wrong. Appreciate any assistance.
- Labels:
-
PSoC 5 Device Programming
-
PSoC 5LP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Santhosh,
A DVK or your own board are you playing?
Suggest double-checking the hardware connection(power domain, switch...), port settings(voltage level, programming mode...).
are the SWD ports required by other tool?
A KBA about programming issue is FYI:
Troubleshooting PSoC® 3/4/5LP Programming/Debugging Issues - KBA210619
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ryan,
It is a custom PSoC board. I was able to program it with Kitprog
successfully. Issue is with the miniprog3.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ryan,
I have gone through the link. I checked the community threads as well. But I am unable to find any description of the issue or a solution.
Hi All,
Any workaround or solutions, please let me know.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Did you already try to update the miniprog3 to latest revivion using PSoC Programmer?
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Bob,
Yes, I updated the miniprog3 but I am unable to program.
Kindly find the log below. Appreciate your help.
"
Program Finished at 02:59:56 |
FAILED! Cannot halt CPU and activate Debug | Please, check the following items: | - the connection between the programmer and the PSoC; | - the correct programming protocol is selected; | - the correct connector option is selected. Program Requested at 02:59:53 |
MiniProg3 version 2.05 Firmware Update Finished at 02:59:46 |
FAILED! FW Version is up-to-date. No need of Upgrade. Hex: 2.05 MiniProg3: 2.05 |
Initializing...
Firmware Upgrade Started at 02:59:46 |
Firmware Upgrade Requested at 02:59:45 |
Successfully Connected to MiniProg3/1609BB000FEF at 02:58:44 | MiniProg3
version 2.05
Opening Port at 02:58:43 |
Memory Types Load from HEX Finished at 02:58:43 |
Device set to CY8C5868AXI-LP035 at 02:58:43 | 262144
FLASH bytes
Device Family set to CY8C5xxxLP at 02:58:42 |
Memory Types Load from HEX Requested at 02:58:41 |
Active HEX file set at 02:58:41 |
E:\Users\CUSE\Documents\PSoC
Creator\Workspace04\BOOST_testing_New_board.cydsn\CortexM3\ARM_GCC_541\Debug\BOOST_testing_New_board.hex
|
| Users must be
aware that the following PSoC device should not be powered or programmed at
5V. Doing so will cause damage to the devices: CY8C6xxx, CYRF89xxx
Session Started at 02:58:41 | PPCOM
Version 29.0
"
On Sun, Dec 23, 2018 at 2:57 AM user_1377889 <community-manager@cypress.com>
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Could you double-check the hardware connection of PSoC5 and MiniProg-3? Use programming cable as short as possible.
Are there any other silicons on your board? MiniProg-3 has limited current sourcing strength.
Double-check VDDD, VDDA, VDDIO, VCCD...is connected correctly.
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Ryan,
Appreciate your assistance.
I checked the voltage levels and the also used the provided 10-pin
connector but getting the same error. But I am able to program it
successfully with PSOC 5lp CY8CKIT_059 successfully.