- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I am trying to establish between the cypress board and the TI toolkit. I am fairly new to the I2C communication. Could the community please direct me to the appropriate tutorials?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Byte I2C interface is quite simple: After setting up the component and starting it you use
I2C_MasterSendStart(DeviceAddress,I2C_WRITE_XFER_MODE); // Initialize a transaction for writing
I2C_MasterWriteByte(Register); // Indicate which register you want to write to
I2C_MasterWriteByte(Value); // Write to register
I2C_MasterSendStop(); // End of transaction
When you want to read from a device you use (example for reading two bytes
I2C_MasterSendStart(DeviceAddress,I2C_WRITE_XFER_MODE); // Initialize a transaction for writing
I2C_MasterWrite(Register); // Indicate which register you want to write to
I2C_MasterSendRestart(DeviceAddress,I2C_READ_XFER_MODE);
I2C_MasterReadByte(I2C_ACK_DATA); // Read from register
I2C_MasterReadByte(I2C_NAK_DATA); // Read from register, last byte is NAKed
I2C_MasterSendStop(); // End of transaction
Not too difficult. Keep in mind that most of the APIs (except those for reading a byte) return a status byte which, when non-zero indicate an error condition.
The high-level APIs must be used in this way:
Writing to slave Count bytes
I2C_MasterWriteBuf(SlaveAddress,DataPtr,Count,I2C_MODE_COMPLETE_XFER);
Reading from Slave sending register/command byte first:
I2C_MasterWriteBuf(SlaveAddress,&RegAddress,1,I2C_MODE_NO_STOP);
I2C_MasterReadBuf(SlaveAddress,DataPtr,Count,I2C_MODE_REPEAT_START);
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Byte I2C interface is quite simple: After setting up the component and starting it you use
I2C_MasterSendStart(DeviceAddress,I2C_WRITE_XFER_MODE); // Initialize a transaction for writing
I2C_MasterWriteByte(Register); // Indicate which register you want to write to
I2C_MasterWriteByte(Value); // Write to register
I2C_MasterSendStop(); // End of transaction
When you want to read from a device you use (example for reading two bytes
I2C_MasterSendStart(DeviceAddress,I2C_WRITE_XFER_MODE); // Initialize a transaction for writing
I2C_MasterWrite(Register); // Indicate which register you want to write to
I2C_MasterSendRestart(DeviceAddress,I2C_READ_XFER_MODE);
I2C_MasterReadByte(I2C_ACK_DATA); // Read from register
I2C_MasterReadByte(I2C_NAK_DATA); // Read from register, last byte is NAKed
I2C_MasterSendStop(); // End of transaction
Not too difficult. Keep in mind that most of the APIs (except those for reading a byte) return a status byte which, when non-zero indicate an error condition.
The high-level APIs must be used in this way:
Writing to slave Count bytes
I2C_MasterWriteBuf(SlaveAddress,DataPtr,Count,I2C_MODE_COMPLETE_XFER);
Reading from Slave sending register/command byte first:
I2C_MasterWriteBuf(SlaveAddress,&RegAddress,1,I2C_MODE_NO_STOP);
I2C_MasterReadBuf(SlaveAddress,DataPtr,Count,I2C_MODE_REPEAT_START);
Bob