- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The scripts referred to in this post are now part of the WICED-SDK2.4.0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
what build string is used? bcm943362wd2? this is the only platform i see the stm32f1xx used - which is the correct processor for the murata sn8200. I wonder if evk is the same version.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Build string parameter should be BCM943362WCD2.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am in a similar situation. I want to reprogram the SN8200 for a standalone SMTP client using the SDK.
I do have olimex openocd working directly in the wiced ide. I never had the sn8200evk - I used the demo units from Farnell/ember to get started. what example files did you get with the evk -( is it the normal sn8200 unit )- which build target is used?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
2.4.0 release is out, but it still seems to generate by default separate binaries for DCT and application. Is there some info how to concatenate them?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I too need this ability. Any new information?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
We are facing same problem with SN8200 module. We are using Wiced SDK 2.4.1 and ST-Link programmer to download our application into our SN8200 PCB. How can we combine these binaries, app.bin , DCT.bin and bootloader.bin, into single binary? Is there any target string available for wiced SDK 2.4.1?
Thanks,
Nipam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I used an olimex openocd and changed the build string to suit. Not all the samples would fit in the chip. I had to mess about with openocd script but it did work well. Not been looking at this lately but I think you need to look at the list of supported targets for the exact micro type.
Target = BCM943362WCD2.
Openocd scripts simply flashed everthing - it was the same setup as the broadcom demo board that murata used for sn8200 (sychip)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Adamtwatson,
Thanks for your response.
Yes Olimex openocd is one option and it is used JTAG pins to download a firmware. But problem is that our designed SN8200 Hardware board has only UART pins which will be used to download a firmware into our SN8200 Hardware board, not JTAG pins. As Murata firmware "SN8200-SNIC-UART-03-37191.bin", available in Murata software kit, is downloaded successfully into our Hardware board using UART but not when Wiced IDE is used. So if I can combine these binaries (App.bin, DCT.bin and bootloader.bin) into single binary, then only I can download my firmware into our designed Hardware board. So is it possible to combine these binaries into single binary?
Thanks,
Nipam