- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So I have a simple task of reading one bit from WICED-WiFi and send a message to a smart phone via Wifi link.
Which current application in the SDK is the best starting point for me?
Thanks
NK
Solved! Go to Solution.
- Labels:
-
SDK 3.x
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Check out this blog about sending an I/O state changes to specified e-mail addresses, http://community.broadcom.com/community/wiced-wifi/wiced-wifi-forums/blog/2014/12/05/email-state-cha...
Perhaps you can set the e-mail address as 10digitphonenumber@txt.att.net to send SMS messages to AT&T phones, 10digitphonenumber@tmomail.net to T-Mobile phones, and 10digitphonenumber@vtext.com to Verizon. Each cell phone provider have a free e-mail to SMS service it can be utilized. for other carriers you may check out The Complete List Of Text Messaging Email Addresses | EmailTextMessages.com.
I hope it helps to resolve your question.
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Check out this blog about sending an I/O state changes to specified e-mail addresses, http://community.broadcom.com/community/wiced-wifi/wiced-wifi-forums/blog/2014/12/05/email-state-cha...
Perhaps you can set the e-mail address as 10digitphonenumber@txt.att.net to send SMS messages to AT&T phones, 10digitphonenumber@tmomail.net to T-Mobile phones, and 10digitphonenumber@vtext.com to Verizon. Each cell phone provider have a free e-mail to SMS service it can be utilized. for other carriers you may check out The Complete List Of Text Messaging Email Addresses | EmailTextMessages.com.
I hope it helps to resolve your question.
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks Seyhan.
I was able to make the push2email file.
Regarding the SSID PASSPHRADE, I am using an open WiFi in a coffee shop
(CoffeeBean) which is open and here is the scan results:
Scan complete in 1363 milliseconds
Waiting for scan results...
Type BSSID RSSI Rate Chan Security SSID
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Push2Email snip application connects to the network defined in the .../apps/snip/push2email/wifi_config_dct.h file. If application directory does not have the wifi_config_dct.h file, the network connection definitions are used from the default .../include/default_wifi_config_dct.h file.
In order to connect to a open network change the "#define CLIENT_AP_SECURITY" definition to "WICED_SECURITY_OPEN" where no pass phrase is needed.
#define CLIENT_AP_SECURITY WICED_SECURITY_OPEN
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Seyhan,
I was able to connect to WiFi.
However, when I push SW1 on the board it fails to send email and says:
Bring network up.
Joining : DDW366.A60E97-2.4G
Successfully joined : DDW366.A60E97-2.4G
Obtaining IPv4 address via DHCP
Setting IPv6 link-local address
IPv4 network ready IP: 192.168.0.20
Getting NTP time... success
Current time is: 2015-07-08T00:58:09.022928
Querying DNS server for smtp.yahoo.com
Successfully retrieved SMTP server IP : 98.139.253.105
Sending email: <WICED device is up, initial LED state is ON.>. FAILED!
Querying DNS server for smtp.yahoo.com
Successfully retrieved SMTP server IP : 98.139.253.105
Sending email: <LED is detected OFF.>. FAILED!
This is what I have in my line 172-176 of push2email.c file.
Should I change any line of it? server port, smtp or encryption?
account.email_address = "nkalantari@yahoo.com"; // or use your email
account
account.user_name = "nkalantari"; // or use your
username
account.password = "Mypassword!"; // or use your
password
account.smtp_server = "smtp.yahoo.com"; // or select your
SMTP server
account.smtp_server_port = 587; // or select
another port
account.smtp_encryption = WICED_EMAIL_ENCRYPTION_TLS; // or
WICED_EMAIL_NO_ENCRYPTION
Regards,
NK
On Mon, Jul 6, 2015 at 12:48 AM, seyhan <
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
It is not tested with yahoo mail.
I will create an yahoo email account and try it.
Seyhan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I tried with my Gmail as well. Same thing .Shall I change any of those
lines?
NK
Nader Kalantari, PhD
Founder & CEO
ArianRF Inc.
Email: nader@arianrf.com
Phone: (949) 246 0848
On Jul 8, 2015 12:35 AM, "seyhan" <communities-list@community.broadcom.com>
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content