- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I have recently updated a PSoC4000s CapSense project from Creator 4.0/ CapSense P4 v3.1 to Creator 4.2 / CapSense P4 v5.2.
In the process I noticed that the Creator Tuner v5.2 "sense tuner" does not connect to my MiniProg3. I Get "Bridge Status: Disconnected"
When I press Connect, I Get: "There was an error reading data from the device"
I have triple checked the EZI2C settings vs the Tuner Com Settings and they are correct. I can use the older Creator 4.0 tuner and it connects right away.
I am a bit stumped, wondering if this is a bug?
Thanks,
Adam
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Adam,
You're welcome. I'm glad to surf in Cypress community.
I tried on PSoC Creator 4.0 with that attached project. Tuner works.
Then opened the project by PSoC Creator 4.2, upgrade components to latest versions, program an run tuner. And it works...
Of course, I tested on CY8CKIT-145. As per my understanding, CY8C4024LQI-S412 has similar hardware IP with CY8C4045AZI-S413. It should work for CY8C4024LQI-S412 too......
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Adam,
Could you share with us your CapSense project? So that we could try to reproduce the issue and find the root cause.
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please have a try as below:
1. delete 'CapSense_RunTuner()' in main().
2. Add CapSense_RunTuner() after return CapSense_IsAnyWidgetActive(); in scanForWidgetActivation();
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
rzzh
I have the same kit and ran your project successfully on it, connecting with the MiniProg3.
I am pretty confident my connections are good (I have checked them so many times now) as the same project made with Creator 4.0 runs the tuner just fine, and this is on the same board that I am testing the 4.2 project on. I am just re flashing the program between Creator versions for this testing.
I am wondering if the chip I am using CY8C4024LQI-S412 is not playing nice with the newer Creator/Tuner/CapSense/EZI2C specifically. Considering the CY8C4045 on the CY8CKIT-145-40xx works correctly.
I am going to attach the creator 4.0 bundle if you want to see if anything is different...
I appreciate the time you are putting into my issue Ryan,
Thank you,
Adam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Adam,
You're welcome. I'm glad to surf in Cypress community.
I tried on PSoC Creator 4.0 with that attached project. Tuner works.
Then opened the project by PSoC Creator 4.2, upgrade components to latest versions, program an run tuner. And it works...
Of course, I tested on CY8CKIT-145. As per my understanding, CY8C4024LQI-S412 has similar hardware IP with CY8C4045AZI-S413. It should work for CY8C4024LQI-S412 too......
Thanks,
Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I tried a new computer with a fresh PSoC Creator 4.2 install and no luck.
In the next few days I am going to reflow fresh PCB's with CY8C4025LQI-S412, maybe a different chip will get me somewhere.