- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am using WICED-Studio-6.1 on CYW943907AEVAL1F platform.
I can't succeed to download the image using by using Olimex_ARM-USB-TINY-H on WICED-Studio-6.1 (Windows10).
but WICED-Studio-6.0 can download successfully.
The failure OpenOCD log is as follows;
-----------------------------------------------------------------------------------------------------------------------------------------------
Open On-Chip Debugger 0.10.0+dev-00225-ga9a9861c (2018-02-06-09:36)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain connect_deassert_srst
trst_and_srst separate srst_nogate trst_push_pull srst_open_drain connect_assert_srst
adapter speed: 100 kHz
adapter_nsrst_delay: 100
Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'.
jtag_ntrst_delay: 100
post_init_psoc6_setup
Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED
Error: libusb_open() failed with LIBUSB_ERROR_ACCESS
Error: no device found
Error: unable to open ftdi device with vid 15ba, pid 002a, description 'Olimex OpenOCD JTAG ARM-USB-TINY-H', serial '*' at bus location '*'
-----------------------------------------------------------------------------------------------------------------------------------------------
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
What is the driver that you are using for Olimex_ARM-USB-TINY-H ? Please use the driver mentioned in 43xxx_Wi-Fi/tools/OpenOCD/Olimex_README.txt and also provide the error message that you are seeing. (download_dct error? )
Relevant help article: OpenOCD -WICED
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you for the answer.
Use driver is libusb-win32 Ver1.2.6.
Error message is as follows;
-----------------------------------------------------------------------------------------------------------------------------------------------
Building apps lookup table
WICED/platform/MCU/BCM4390x/BCM94390x_targets.mk:340: recipe for target 'download_dct' failed
make.exe[1]: *** [download_dct] Error 1
make.exe[1]: *** Waiting for unfinished jobs....
Makefile:349: recipe for target 'main_app' failed
make: *** [main_app] Error 2
-----------------------------------------------------------------------------------------------------------------------------------------------
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am assuming status of the SW4 is all ON and then also you are receiving this error? I tested with 6.1.0.85 SDK and I was able to download successfully without manually updating the driver. For your case, you can try updating the driver by choosing the option of search automatically for the updated software in your WINDOWS 10 PC and you should be able to download if you have followed all the steps correctly as mentioned in OpenOCD -WICED
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi morise,
Did you resolve "download_dct" failed issue? Because I have met same issue with you, I'd like to ask how did you resolve this issue if you resolved? I also use "libusb-win32 ver 1.2.6" and SDK 6.1.0 or SDK 6.0.0 but it still doesn't work.
Test EVK is same with you(CYW943907AEVAL1F and Olimex ARM-USB-TINY-H). Could you give a guide?
Thanks,
Liam