Anonymous
Not applicable
Feb 24, 2015
07:36 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
07:36 AM
9 Replies
Feb 24, 2015
07:49 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
07:49 AM
Great post but use of invisible text not allowed.
Anonymous
Not applicable
Feb 24, 2015
07:52 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
07:52 AM
Hello, First of all I want to say sorry, I couldn't write in the first post, I think it was because I was using Chrome. I am in a Project in which I have to read several sensor and send the information to a external device by bluetooth, in real time and also record measures and after some time send those data. I would like to use the HCI mode to send the recorded measures but I can't connect the bluetooth, the Cyble_start doesn't init the BLE what can I do? I have also tried to use the custom service with some custom attributes but y don't know how to send the data. could anybody help me? Thank you
Feb 24, 2015
08:26 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
08:26 AM
Take a look at the projects (10+) here, might be adaptable to what
you want -
http://www.cypress.com/?id=5509&StartRow=6&PageNum=2
Regards, Dana.
Anonymous
Not applicable
Feb 24, 2015
11:46 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
11:46 AM
Thanks Dana, There I can see some projects about custom service but, do you know where I could find some information for HCI-Mode (Host controller Interface mode Bluetooth Uart)?
Feb 24, 2015
12:11 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
12:11 PM
You havbe seen these where the HCI layer is discussed ?
http://www.cypress.com/?rID=102505 AN94020
http://www.cypress.com/?rID=102504 AN91267
Regards, Dana.
Feb 24, 2015
02:17 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 24, 2015
02:17 PM
I'm afraid there is not much information about the HCI mode. Did you try to configure th BLE component in HCI mode and see what code is generated?
Anonymous
Not applicable
Feb 26, 2015
11:26 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 26, 2015
11:26 AM
Yes I did, but I can't find how to stablice the connection. I will keep looking for the solution, thanks.
Anonymous
Not applicable
Feb 26, 2015
11:48 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 26, 2015
11:48 AM
Dana I don´t know where you meant, but i have seen both pdf files in the links.
Anonymous
Not applicable
Mar 03, 2015
06:31 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 03, 2015
06:31 AM
Marco,
When component is configured in HCI mode, a UART interface is provided by the component. You can select the UART pins as per your hardware and start sending the standard HCI commands over UART.
All the BLE HCI commands (defined in BLE spec) are supported by the component.
Regards,
Rahul