• libusb Error when Programming Using openOCD CLI or ModusToolbox – KBA231563

    Author: VitaS_81           Version: **   Problem:  Programming a PSoC® 4 or PSoC 6 MCU device with MiniProg4 or KitProg3 fails. An ‘unable to get list...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Cannot Use MiniProg4 and J-Link Probes in JTAG Interface when Deep Sleep Mode Is Switched ON – KBA231562

    Author: VitaS_81           Version: **   Problem: When attempting to program/debug a PSoC 6 MCU device with MiniProg4 or J-Link probes in the JTAG interface, the foll...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Using Eclipse IDE for ModusToolbox 2.1 after Installing ModusToolbox 2.2 - KBA231606

    Version: **   Question: After installing ModusToolbox 2.2, why am I seeing an error while attempting to program or debug using the Eclipse IDE installed with ModusToolbox 2.1?   error while launching comman...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • CX3 Firmware: Frequently Asked Questions - KBA91297

    Version: *C   1. Question Where can I find the CX3 firmware source code for example projects?   Answer You can find the CX3 firmware example projects as part of the FX3 SDK 1.3.1 or later release. These p...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • How to create a Bluetooth Mesh Low Power Node (LPN) - KBA231327

    Version: **   This article explains how to enable Bluetooth Mesh Low Power Feature in the mesh vendor model app (Vendor_specific_app).   The Bluetooth Mesh specification (SIG spec) defines the Low Power feat...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • CCG3 FAQS - KBA226666

    Author: HirotakaT_91        Version: *E     Hardware Question: What is the power consumption on the VDDD pin on CCG3? Answer: If VDDD = 5 V, typical current consumption is 25 mA...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Log Data in Bridge Control Panel (BCP) using MiniProg3 (UART) for PSoC 3/4/5LP Devices - KBA231530

    Version: **   Follow these steps to log data in the Bridge Control Panel (BCP) with the help of the RX8 protocol (UART), using MiniProg3 for PSoC 3/4/5LP devices: 1. Set up a UART interface with the required pin...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • PSoC® Creator™: ECO/EXCO Issue with Quartz Crystals and Ceramic Resonators Driving the PLL - KBA231127

    Version: **   Problem:On the PSoC 4100S Plus, and PSoC 4500 device families when the ECO clock is configured via DWR or using cy_boot API, the redundant EXCO_PGM_CLK manipulation destabilizes the PLL. This then r...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • ModusToolbox 2.2 and later: Make a Custom BSP - KBA231373

    Version: **   Question: How do I create a custom Board Support Package (BSP) for my own hardware?   Answer: Follow the steps in this article. This article is for ModusToolbox v2.2 and later. Some details...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • PSoC 4 Opamp Input Voltage Noise Density Graph – KBA231398

    Version: **   Device operating voltages and sensor voltages have been reducing over time. This makes noise, an important factor when you work with Opamp. Knowing the changes in Opamp noise density with frequency...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • pow() function in EZ-USB Suite - KBA231148

    Version: **   The pow(a,b) function returns the value of ‘a’ raised to the power of ‘b’. It is defined inside the math.h header file. Do the following to use this function in an FX3 projec...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • FX3 SPI boot fails when S25FS128S flash is used – KBA231163

    Version: **   By default, the S25FS128S flash device comes with hybrid sectors (the first sector of 64KB divided into 9 sectors (8 sectors of 4KB and one 32KB sector).  All remaining sectors are uniform (64...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • I2C_Stop() API Does Not Disable I2C Master in I2C Component v3.50 of PSoC 3 and PSoC 5LP - KBA231344

    Author: RakshithM_16      Version: **   When the I2C Component v3.50 is used in I2C Master mode with Fixed function implementation, the I2C_Stop() API does not disable the master. This is...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • MM MCU Part Nomenclature - KBA231343

    Version: **   Question: What is the part numbering conventions for MM MCU devices?   Answer: The two types of part numbering conventions for MM MCU devices are: MB Part Number System (ex-Fujitsu) SIL Par...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Can Semper S28HS-T/S28HL-T Octal Flash operate in either QPI or QSPI mode? – KBA231294

    Author: AlbertB_56           Version: **   There is no provision to support either QPI or QSPI modes of operation.  The Semper™ S28HS-T and S28HL-T  se...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Tools Directory not found in ModusToolbox 2.x – KBA231392

    Author: DheerajK_81           Version: **   Question: When I build my application in ModusToolbox® 2.x on Windows, I get the following error: Makefile:163...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • PD COMPLIANCE TEST FAQS - KBA29887

      Author: YiZ_31           Version: ** Question: What are benefits of passing PD compliance test? Answer: The Compliance Program of USB-IF uses multiple test specifi...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • Migrating from PSoC 6 BSP v1.x to v2.x in ModusToolbox v2.2 – KBA231266

    Version: **   This KBA describes changes and new features introduced by the Board Support Package (BSP) v2.x release which impact ModusToolbox applications using BSP v1.x (latest-v1.X tag) and provides informatio...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • MIGRATING APPLICATIONS FROM MODUSTOOLBOX V2.0/2.1 TO V2.2 - KBA231080

    Version: **   Note: If you are migrating an application created for an older version of ModusToolbox® (v1.1) refer to Migrating from ModusToolbox v1.1 to v2.x - KBA229043.   ModusToolbox 2.2 fully suppo...
    ChaitanyaV_61
    last modified by ChaitanyaV_61
  • ModusToolbox Warning: Uncommitted/Untracked Files Detected - KBA231252

    Version: ** Question: Why does my ModusToolbox application report a warning about uncommitted/untracked files? Answer: Some firmware compiled into a ModusToolbox application is generated by configurators. The ModusT...
    ChaitanyaV_61
    last modified by ChaitanyaV_61