to follow, share, and participate in this community.
Hi we are planning to use BLE module from Murata(Type 1GR) with CYW20736 and interface it externally with STM32F412 to write our application , Can you let me know which platform on WICED I need to use for the developm... Upon downloading and installing the windows version of the WICED Smart SDK, I can compile without errors by selecting a target. But the Eclipse IDE seems to be using a different compiler, and gives me a bunch of... Hi, I am trying to use CYBLE_0130025 Eval board to learn EZ Serial Binary command mode. I have kept Switch 1-4 in OFF position and Switch 5-6 ON Position. I am using Realterm to see if after se... Hi to everyone, Last weeks I've been working on the connection between the bcm20737 and my custom Android app. For my application I don't need bonding neither ... P_UART question There may be two sets of P_UART pins P32 (Tx) and P33 (Rx) P0 (Tx) and P2 (Rx) I have used P32/P33 for debug traces. Would it be possible to use the following set-ups at the same time? Use P32/P... I have met a problem.if my device bounded with a phone,other phones will could not bound with this device.I gess in my device,if i should release bound. Hello everyone. I have the following problem. When I put in the code blecen_Scan the timer 1s stopped working. Has anyone ever had a similar problem? I have 4 devices communicating in a Bluetooth piconet, where 1 device is the master device and 3 devices are slave devices. I want to time synchronize the 4 devices to within 1 millisecond using Bluetooth comm... I have a piconet of 4 devices, where 1 device is a master and 3 devices are slave. Communication continuously occurs between master and the slaves. But then the master is shutdown at an arbitrary time.... hi,all I have a project plan to use CYW20736 for motion sensor with Apple HomeKit BLE ； Now, where can download the newset HomeKit BLE SDK for CYW20736? Thanks! I recently purchased the BCM9WICED_SENSE2 Evaluation and Development Kit and the iOS WICED Sense app doesn't exist in iTunes app store. Is there any plan for Cypress to post the app that was there before? ... Hi,where can I download the datasheet about CYW20707(BCM20707),tanks. I just bought WICED Sense 2 kit. Can I use WICED Smart IDE v2.x to download the code to it and debug it? This kit is TAG4 type, isn't it? Does WICED Sense 2 kit work with iPhone 5 SE? I tried to look for its app on my iphone 5 se and I could not find it. Light Blue LE can see it. Hi, I have two problem. The first, I developed BLE product using BCM920737TAG-03 and SDK2.2.3 under windows 10. When it compiled(built), errors was occured as blow. "makefile:184: recipe for target '... Hi, I'm using a BCM92073X_LE_KIT, connected to WICED SDK, it has been working fine for the past few months, however today it has stopped working. Nothing can be seen through the UART terminals. ... Hi all, RH readings from wiced sense 2 using the official android app seems to be 15 to 20 units (RH %) higher than real RH. Also the RH reading is not updated (waited 10 min) ; is updated only when I discon... All the guages on my Wiced Sense IOS App work correctly but temperature and humidity do not change when the tag is exposed to tempeature and humidity fluctuations. Are there any know n issues? Not sure about the pres... Hello ! I just bought 2 wiced-sense units and testing then with the android application (updated both to 1.3 detected and done on the first run) one of then do not show compass information properly the values only va... Hello ! I'm testing wiced-sense with the iOS and Android applications provided by Broadcom and noticed that they have 90 degrees indication difference: - With iOS application connect to the wiced-sense and po...
Get a feed of this content