PSoC™ 6 Forum Discussions
Dear supporter,
I would like to translate the following KBA. Could you confirm?
PSoC™ 6 MCU with Bluetooth® LE: Reading sleep clock accuracy – KBA238648
https://community.infineon.com/t5/Knowledge-Base-Articles/PSoC-6-MCU-with-Bluetooth-LE-Reading-sleep-clock-accuracy-KBA238648/ta-p/690974
Bestregars,
JUTA_2823561
We are requirement of supporting I2C master-slave mode for our I2C1 port. Can I Get some example regarding the same.
Dear Forum:
I do many test, I find the following phenomenon:
Before set MCU to Deep Sleep,
If I don't clear the SSR(serial status register) bit before close SPI,
MCU(PSoC6) can't enter deepsleep.
If I clear the SSR(serial status register) bit before close SPI,
MCU(PSoC6) can enter deepsleep.
I want to confirm:
does the SPI SSR bit affect MCU deepsleep or not.
Thank you.
Show LessI own Rev11 of PSoC6 BLE PIONEER KIT.
What kind of support can I get?
Hi Community,
I am currently exploring the utilization of a CYKIT-028 TFT Module in conjunction with both Raspberry Pi and ESP32 microcontrollers. However, I find myself in a bit of a quandary regarding the choice of IDE (Integrated Development Environment) and the necessity of using PSOC Creator.
Given my familiarity with PSOC Creator for working with PSOC4 MCUs in my professional capacity, I wonder if it is imperative to continue using PSOC Creator for interfacing with the CYKIT-028 TFT Module, or if there are alternative IDEs compatible with this display module. Additionally, I am seeking clarification on whether the TFT module can be seamlessly integrated with microcontrollers beyond the PSOC family, such as Raspberry Pi and ESP32.
Show LessHello,
I am developing a BLE peripheral device based on the code example. The firmware is running in FreeRTOS, and low-power approaches are implemented.
Currently, I am using a single core configuration. A ble_task is created which initializes the BLE, registers the stackEventHandler, also registers AppHostCallback. In the for(;;) loop, it processes the command related to BLE.
I want to know how much STACK_SIZE should be set for the ble_task, when I call the xTaskCreate() in main_cm4.c.
ble_create=xTaskCreate(ble_task, "BLE Task", TASK_BLE_STACK_SIZE,NULL, TASK_BLE_PRIORITY, NULL);
I am worried that, if TASK_BLE_STACK_SIZE is not enough, the MCU cannot process the BLE event correctly.
Thanks for kindly reading my question, any suggestion or comments are highly appreciated.
Best.
Show Less使用cy8c6347,请问如何很精确的发出固定数目的脉冲?使用定时器好一点还是利用脉冲产生的中断来计数更精确?
When testing this routine, following the steps in Readme, Testing with AIROC ™ Bluetooth ® Connect App on Android, it was found that apps using Android can successfully connect, but those using iOS cannot, as shown in the figure. Later, I used bleak Python to write a GATT client program and attempted to establish a connection with the BLE board, but encountered the same error as the IOS App and was unable to connect. May I ask how I can solve it
Show Less
Hi
I need to write 2 pieces of data, each is 5-bits.
The first is written to port-9 pins 0 to 4 (P9.0, P9.1, P9.2, P9.3, P9.4). This is done using GPIO_PRT_OUT()
The second is written to P9.5, P9.6, P5.4, P5.5, P5.6. What is an efficient method to split the second data word (5-bits) among bits in 2 ports ?
Thanks
Show Less