Log in to follow, share, and participate in this community.
Module using "ISM43362-M3G-L44-E/U serial-to-Wifi" . Testing on wiced studio version 6.4.0.How to flash/debug code using stlink /ulink debugger. How to flash/debug Inventek wifi modules?
BackWhat are the key differences between OTA and OTA2 in WICED? Do either allow partial update - WiFi Stack only / BLE Stack only / User Application only? Do both provide ability for code verification? ... I'm trying to use the Inventek ISMART43340-C modules but there aren't any factory support for the WICED software to run the packet_filter.c snip. What do I have to do to make this module work for this example? ... Inventek ISMART43340-C module running packet_filter.c snip
BackDeclaration ID: D040194 QDID: 115853 The CY-WICED stack here is based on WICED and is the current Cypress Bluetooth stack: https://launchstudio.bluetooth.com/ListingDetails/65279 CY-WICED was derived... WICED Studio 6.2.1 WICED-Studio 6.2.1 Installer (Windows) WICED-Studio-6.2.1 (OSX) WICED-Studio-6.2.1 (Linux 64-bit) Release Notes: WICED Studio 6.2 Release Notes: WICED Studio 6.2.1 Technical Brief: WICED Studi... We have an existing product already on the market that uses a module with the 4343W silicon and shipped with bootloader and the original OTA (not OTA2) code from WICED SDK 4.1.1. We would like to OTA to an updat... WICED Studio 6.1.0 WICED-Studio 6.1.0 Installer (Windows) WICED-Studio-6.1.0 (OSX) WICED-Studio-6.1.0 (Linux 64-bit) Release Notes: WICED Studio 6.1.0 WICED Studio 6.x Technical Brief =========================... Hey, We just went over 2016 IoT Solutions Guide and saw that some BCM modules offer WICED while others offer Virtual WICED. Can someone please explain what's the difference between the two? Tha... To stay on top of this training series and others, make sure you follow the Training Center to your inbox: WICED Wi-Fi 101: Chapter 1 WICED Wi-Fi 101: Chapter 2 WICED Wi-Fi 101: Chapter 3 WICED Wi-Fi 101:... You do not have access to this content's place WICED Studio 5.2.1 has been released (backport to address KRACK)
Shared by MichaelF_56
BackYou do not have access to this content's place WICED Studio 4.3.1 has been released (backport to address KRACK)
Shared by MichaelF_56
Back**WICED Studio 6.0.0: WICED-Studio 6.0.0 Installer (Windows) WICED-Studio-6.0.0 (OSX) WICED-Studio-6.0.0 (Linux 64-bit) Release Notes: WICED Studio 6.0.0 Note: The Linux 32-bit Installer is no longer sup... Hi guys, I am using version 3.7.0 of the WICED SDK. I have added support for the STM32F479 discovery kit; the support was mostly there, just a few missing IFDEFs. I believe that everything is working properly. ... STM32F469 Discovery - BCM43340
BackI have a couple proto-type units based on the lightbulb service example. They are using the Inventek Systems ISM43341-M4G-L44 Wi-Fi module. In a week of testing using my iPad as the home base, the units sh... Issues with remote access through Apple TV
BackDevelop IoT applications with this mixed signal configurable MCU + Radio IoT Development Platform bundle, featuring Cypress and Inventek solutions with AWS Cloud application software Inventek’s ISMART (In... ISMART + PSoC® 4 MCU Mixed-Signal Configurable MCU + Radio IoT Dev. Platform
Appears in 1 other place
BackX-CUBE-AWS runs on three platforms. The B-L475E-IOT01 board supports WiFi® connectivity with an on-board Inventek module. It is equipped with a set of sensors able to report: humidity, temperature, 3-axis magneti... Inventek based AWS IoT software expansion for STM32Cube
Appears in 1 other place
BackHi, I am working on ISM43362 EVB (almost same with BCM943362 EVB) which contain BCM43362 Radio and STM32F205RGY6 (64Pin BGA Package). I could download and run with the help of Broadcom Wiced SDK IDE. I mean the FW an... Problem when loading Firmware into ISM43362 EVB
BackHi, I am using the Inventek ISM43341 module with WICED SDK 3.5.2. I have the Inventek module configured to be in soft AP mode, and I have a linux PC client sending UDP packets. I am sending 128 byte packets at... System hanging after receiving UDP packets
BackI'm attempting to use the BCM43341 (via the Inventek ISM43341 module) to implement NFC Peer To Peer mode using WICED SDK 3.5.2. The issue I'm running into is that the WICED NFC API seems to only support reader/writer ... BCM43341 NFC Peer To Peer Mode
BackHi. I have ported the platform files for 3.5.2 MFI on the WICED 3.7.0 MFI SDK for the ISM43341_M4G_L44 platform. snip.scan works well. However snip.bluetooth.ble_proximity_reporter hangs after boot. It... 3.7.0 Bluetooth Proximity Reporter on ISM43341_M4G_L44
Back