to follow, share, and participate in this community.
I’m working on OTA updates now and (hopefully) only have a minor issue. I found the Android updating app and installed it to my phone – it looks like it is working. I found the sample app and copi... Similar to these 2 community posts (which discuss PSoC 4 and 6 devices), https://community.cypress.com/thread/35936?start=0&tstart=0 https://community.cypress.com/message/159506#159506 is it possi... Hello Cypress IoT team This thread is related to below. https://community.cypress.com/thread/50272 We evaluate CYW20819 with MoodusToolBox. Under our evaluation, when watchdog timer(WDT) exceeds timeo... Hello Cypress IoT team We evaluate SPP transfer with the attached code "spp.c". If they comment out following codes, CYW20819 aborts the transfer and looks like hang up. -Line 284: wiced_rtos_delay_milliseco... Hello, Is there an easy way to just flash the firmware binaries instead of programming the board from the source code? I want to program the boards to use the mesh examples - dimmer,lighting , etc. Any progra... Dear All, We are going to use the PUART not HCI UART due to security reasons. So we need to update our F/W through PUART. I could find the OTA upgrade application but there is no PUART updating application. ... Hi Cypress CYBT-213043 driver issue , Can you get how to install the driver for ModusToolbox 2.0 , Thank !! Until the mesh controller smartphone app is available in Google's Play Store, where can the application be found (without finding and downloading a previous version of ModusToolbox)? Note: Two posts I could fi... Hello, I would like to use the Client Control Mesh for Window10. My conditions are below. - ModusToolbox1.1+BTSDK1.4. - CYBT-213043-MESH evaluation boards - "ClientCont... I don't know what this means, i was trying to launch the mesh demo. I already ran Wiced once before so I don't understand whats going on here. HI, related to Coexistance of beacon Eddystone and iBeacon with mesh functionality and DheerajP_41 answer, I did some tests and I have complicated the example a little to make it more realistic. I notice... Hi: I download the mesh_provision_client firmware to my CYW920735Q60EVB-01 board , and use mesh client control to create a network and a bt mesh device has been added into the created netwo... Hello. I am working on the Android MeshApp but I have some doubts. I see I have little control with the devices models. I can turn on and off the LEDs and dimmer them and set LC properties. I am missing Configurat... I've got the PSoC 6 BLE Pioneer Kit (CY8CKIT-062-BLE). I would like to work on a new project, all in ModusToolbox. I'm looking for an example of this kit interfacing with the CySmart app via BLE but I can't find any. ... Hi I am using the CYW920819EVB-02 Evaluation Kit and the range for the BLE5 is only a meter if not less. I am running the beacon program and the battery level program with the same results to my Samsung 10e. Running o... I am having problem with CYBT-213043 kits when powering from CR2032 slot. It works fine when battery voltage is above 2.9 V to 3.3 V (fresh battery).But when voltage drops below 2.9 volt, the bluetooth chip turns off ... I was trying to send files from board(imx6) to phone(android) via bluetooth obexftp -b <mac_addr> -p filename (file in board) But I was not able get that file in phone. When I installed ES file explorer it was... hi, I want to update firmware to cyw20819 using hci uart. I have successfully upgrade cyw20819 with minidriver.hex and mainapp.hex, and ... Hello Cypress IoT Team We evaluate CYW20819 with ModusToolBox. Regarding API stack size, we referred to the below. Code-Examples-BT-SDK-for-ModusToolbox-master\CYW920819EVB-02\apps\demo\datalogger\d... Hello Cypress IoT team We evaluate CYW20819 with ModusToolBox for their next products. Let us confirm about timeout_ms in "wiced_rtos_wait_for_event_flags". == wiced_result_t wiced_rtos_wait_for_event_flags ...
Get a feed of this content