to follow, share, and participate in this community.
Author: TakashiM_61 Version: ** Question: Why are the SCIS01 and SCIS23 registers accessed with 8 bits in adc.c, even though these registers have a width ... Author: HirotakaT_91 Version: *E Hardware Question: Are there any restrictions in the powering ON/OFF sequence of VBUS_US (pin 17) in CYUSB2304-68LT... Author: HirotakaT_91 Version: *E ハードウェアに関するご質問 Question: CYUSB2304-68LTXIのVBUS_US(17ピン)において、パワーオン/パワーオフシーケンスに何か制限はありますか？ Answer: 特に制限はありません。VBUS_USは3.3 V... Author: JeetendraA_51 Version: *A Question: What are the differences between PSoC® 4100S Plus and PSoC 4100S family of devices? Answer: The PSoC 4100... Author: TakashiM_61 Version: ** Question: Which is the correct USB1 base address, the definition in FM4 series header files in PDL 2.1.0, or that provided in FM4 Fa... Author: EktaN_26 Version: ** PSoC 4100S Plus devices always start up using the IMO; the ExtClk can only be enabled in the user application during runtime. ... Author: AH_96 Version: ** Question: Is it possible to obtain the IDAC value from autocalibration once while programming and use it during subsequent power... Version: ** Question: How do I make a channel switch announcement to devices connected as stations (STA) to a device acting as Access Point (AP)? Answer: Channel switch announcement (CSA) is a mechanism for an AP t... Author: RaktimR_11 Version: ** CYW43455 is a single-input single-output (SISO) chip; therefore, it is capable of being only an 802.11ac explicit bea... Author: DheerajK_81 Version: ** Question: When I create a project, PSoC® Creator™ throws the error message: “PSoC Creator Error prj:... Author: RyanZ_36 Version: ** The actual IDAC current value (in µA) of PSoC® 4 CapSense® can be calculated with the following equation: IDAC_... Author: TakashiM_61 Version: ** The enumerator “en_mfs_mode” in PDL 2.1.0 is defined as following. <PDL installation directory>\drivers\mfs\mfs.h //... Author: RyanZ_36 Version: ** The PSoC® 4 Bootloader Component provides a Custom Interface that you can use for developing your own bootloader interfac... Author: GeonaM_26 Version: ** During flash write, the device power supply must be stable and device must not be reset. Otherwise, flash operations will be inte... Author: AlbertB_56 Version: ** The purpose of the ‘HOLD#’ function is to pause any serial communications between the SPI Flash memory d... Author: GeonaM_26 Version: ** In a BLE GATT Server, the BLE advertisement type can be updated. You can stop the advertisement, update the advertisement typ... Author: WangS_81 Version: ** It’s feasible to short VBACKUP to VDDD for the PSoC® 6 MCU device with the BACKUP domain if the dedicated supp... Author: LisaZ_26 Version: ** Ensure the following to enable Ground Sense: Wire the measured ground pin to the positive side of the current sense r... Community Translated by MoTa_728816 Version : ** 質問： PSoC 3, PSoC 5LP ブートローダ用のアプリケーションコードとデータファイル (.cyacd) の形式を教えてください。 回答： “... Author: shusakus_56 Version: ** Question: After the transition from the Power Saving State (PSS) mode to RUN mode, how can I check if the power domain (PD)...
Get a feed of this content