to follow, share, and participate in this community.
Author: DheerajK_81 Version: ** Question: I want to install Eclipse plugins in ModusToolbox. How do I proceed? Answer: ModusToolbox™ 1.1 ... Author: DheerajK_81 Version: ** Do the following to set up and use Git for an Eclipse project in ModusToolbox™: Step1: Updating the Git plugin ... Author: DheerajK_81 Version: ** Question: How can the GCC warnings be diagnosed in PSoC Creator™? Answer: PSoC Creator uses the GCC compiler ... Author: ShipingW_81 Version: *A Question: How do I set the stack and heap for PSoC® 6 MCU devices? Answer: To modify the stack/heap size f... Author: ShipingW_81 Version: ** For PSoC 6 MCU devices, sometimes there would be overswing shown on the GPIO digital output waveform, as shown below. ... Author: ShipingW_81 Version: ** Question: What is the correct way to use internal LDO regulator and SIMO buck regulator for PSoC® 6 MCU device? ... Author: ShipingW_81 Version: ** For PSoC 6 MCU, the RTC (WCO primarily) consumes around 380 nA typical and 1 µA max current; therefore, the powe... Author: XZNG Version: *A Question: In PSoC® 6, how can I route the internal clock out to a pin for other purposes? Answer: For all PSoC 6 parts, the o... Author: XZNG Version: *A Question: How can I keep the UART baud rate stable if the peripheral clock (Clk_Peri) is dynamically changed for low power designs in PSoC® 6? &... Author: SergiiV_71 Version: ** Question: Why fault occurs when Cy_USBFS_Dev_Drv_Disable() is called with USBFS driver endpoint management mode configured to CPU Manual... Author: LinglingG_46 Version: ** Question: Is there a power sequence required for different supplies such as VDDD, VBACKUP, VDDIO, and VDDA in PSoC® 6? Answe... Author: GeonaM_26 Version: ** Question: How do you set BLE transmit power level over Host Controller Interface (HCI) mode in PSoC® 6 MCU BLE? ... Author: LinglingG_46 Version: ** Question: Can I use the PSoC6 BLE Pioneer Kit as a programmer to program external PSoC® devices? Answer:... Author: ShanmathiN_06 Version: ** The SCB_EZI2C_PDL Component can wake up the device from Deep Sleep mode on a Slave address match. To enable this function... Author: VitaS_81 Version: ** Question: I am using PSoC® Creator™ 4.2, PDL 3.1.0, and PSoC Programmer 3.28 tools and trying to debug the CM4 core... Author: SrikanthD_56 Version: *A PSoC 6 MCU on some of the early PSoC 6 BLE Pioneer Kit (CY8CKIT-062-BLE) and PSoC 6 WiFi-BT Pioneer Kit (CY8CKIT-062-WiFiB... Author: DheerajK_81 Version: ** Question: Why Opamp OA0 output is not available in the pin 9 while OA1 output is working fine with the same Opamp settings? ... Author: ShipingW_81 Version: ** Question: How can I generate a combined hex file merging both app0 and app1 for a basic device firmware update for PSo... Author: OleksandrP_61 Version: ** Context: PSoC® Creator™ 4.2 project with the Em_EEPROM Component v2_0, v2_10 or v2_20, for PSoC 3, PSoC 4, PSoC 5LP, ... Author: WangS_81 Version: ** The access to the SMIF block can be by two modes: MMIO mode or XIP mode. The MMIO mode lets you use the QSPI block as a p...
Get a feed of this content