to follow, share, and participate in this community.
Version: ** Question 1: What version of Bluetooth is supported in PSoC® 6 MCU with BLE? Answer: PSoC 6 MCU with BLE is a Bluetooth 5-compliant device. Question 2: Does PSoC 6 MCU with... Version: ** Question: Using µVision IDE with the ULink2 probe, either CMSIS-DAP or JTAG protocol, programming a PSoC 6 device fails. Why? Answer: This is a known issue with PSoC 6 devices and Keil uVisio... Version: ** Question: Which are the PDL versions that support PSoC 6 MCU or FM Microcontrollers? Answer: This table lists various PDL versions and the device families that each version supports: PDL Ve... Version: ** Question: Can a PSoC® 6 MCU GPIO work at 100-MHz speed? Answer: 100 MHz is the maximum GPIO frequency in/out for PSoC 6 MCU. Even though it is capable of 100-MHz GPIO out, no periphera... Version: ** Question: What are the current limitations and known issues with the CY8CKIT-062-BLE PSoC 6 BLE Pioneer Kit and PSoC Creator 4.2 Beta software? Answer: Refer to the following documents to un... Version: ** Question: How do I connect SCB SPI pins to SmartIO? The error “E2809: Unable to find a valid placement for pins and fixed-function blocks.” appears while trying to connect. Answer... Version: *A Question: What are the differences between Cortex-M0 and Cortex-M0+? Answer: The Cortex-M0+ processor builds on the Cortex-M0 processor, retaining the full instruction set and tool comp... Version: ** Question: Why does my project not compile after updating PSoC Creator 4.2? Answer: If you have an earlier version of PSoC Creator 4.2 installed (from the Beta community, for example), and you... Version: ** Question: How do I verify if my CY8CKIT-062-BLE PSoC 6 BLE Pioneer kit has the latest version of PSoC® 6 MCU with Bluetooth Low Energy (BLE) device? Answer: Latest version of PSoC 6 MCU ... Version: ** Question: A building error might occur for PSoC® 6 projects in which both cores occupy the working flash. How can I manage the working flash space for both cores properly? Answer: ... Version: ** Question: External flash in the S25FL512SAGMFI011 device can be read or written through the PSoC® 6 SMIF interface. How can I correctly erase and write to make full use of its storage capacity?... Version: *A Question: What are the main differences between the software architecture of PSoC® 4 and PSoC 6 MCU? Can I port PSoC 4 firmware directly to a PSoC 6 MCU? Answer: The firmware create... Version: ** Question: My executable program has already been downloaded to the target. How do I start debugging without downloading the executable again? Answer: The debug configurations that come with M... Version: ** 问题: 在 ModusToolbox™中，应如何开启 PSoC® 6 的调试过程？ 回答: 1. 在Project Explorer中选中一个工程 2. 在Quick Panel中下拉滚轴至Launches 3.... Version: ** 本文提供了PSoC 6 MCU 资源的完整列表，可帮助您开始使用该器件并用它设计应用程序。如果您刚接触PSoC，赛普拉斯在 www.cypress.com 上提供了大量资源，以帮助您选择正确的PSoC设备，可以快速有效地将其集成到您的设计中。 以下是PSoC 6 MCU资源的简要列表: 概观:PSoC产品PSoC产品路线图PSoC 6 MCU网页 产品选择:请参阅“... Version: ** 问题: 如何区分CY8CKIT-062-BLE开发板是否搭载了最新版本的PSoC 6 BLE芯片？ 回答: 最新版本的PSoC 6 BLE芯片序列号是CY8C6347BZI-BLD53ES3，其中“ES3” 即表示最新版本。可以通过查看开发板上PSoC 6芯片上面的序列号进行确认，如图1所示。 同样也可以核查开发板背面标签贴纸上所标记的版本信息，如图2所示。&ldq... Version: ** SCB_EZI2C_PDL组件可以通过从设备地址匹配唤醒深度睡眠模式下的PSoC 6设备。为此，需要使能Enable Wakeup from Deep Sleep Mode参数。图1和图2分别展示了PSoC Creator 4.2和ModusToolbox中所需的配置。 图1. PSoC Creator 4.2中的配置 图2. ModusToolbox Dev... Version: ** 问题: 对于PSoC® 6, 如何将内部时钟路由至外部引脚作为其他用途？ 回答: 对于所有的PSoC 6器件，时钟输出CLK_HF均可以通过P0和P0路由至外部。所有的时钟源（IMO, ECO, EXTCLK, BLE ECO, ILO, PLIO, WCO, 数字信号）均可以通过内部时钟路径路由作为CLK_HF的输入，因此从P0或P0可以直接（... Author: AnkitaS_51 Version: ** Question: Why is CY_CPU_CORTEX_M0P not defined while editing firmware or code in PSoC Creator™ 4.2 for PSoC®... Author: AnkitaS_51 Version: ** Question: Why do I get the “compilation terminated” build error during compilation of Mbed OS-based projects for ...
Get a feed of this content