to follow, share, and participate in this community.
Community Translated by MoTa_728816 Version : ** 質問：CY7C9689A の FIT (Failure in Time) 値、または MTBF (平均故障間隔時間) はどのくらいですか？ 回答：CY7C9689A の FIT値は 3... Version: *A Question: How do nodes in a clock extension peripheral interface (CXPI) network detect data collision? Answer: In normal state, each node always compares the bit received from the CXPI ... Question: What tools do I need in order to develop applications for the Neuron Chip? Answer: Cypress does not offer any development tools for their Neuron Chips. All development tools are available fro... Question: I am having issues with my Neuron software/compiler and my application code, where should I go for support? Answer: Since Echelon creates most of the software and firmware for the Neuron product, t... Version: ** Question: What should I check for when the PLC Control Panel cannot connect to the PLC device? Answer: Check for the following when this error is displayed by the Control Panel: Is an... Question: Do you have any options for the transformers used in the PLC High Voltage Reference Design? Answer: We have tested options for the following two transformers: Isolation Transformer fo... Question: What should be done with unused serial inputs and outputs on HOTLink CY7B923/CY7B933? Answer: Unused serial outputs on CY7B923 can be either tied to Vcc or left floating to reduce power. One input o... Version: ** Question: Where can you find the datasheet for the Ultra37K (CY37xxx) device? Answer: The datasheet for the Ultra37K device is Cypress specification 38-03007, Ultra37000 CPLD Family, 5 V and... Version: ** Question: Does ISR 4.0.1 programming software have driver support for Windows® 7? Answer: No, the ISR 4.0.1 programming software does not have driver support for the Windows 7 platform.... Version: ** Question: Where can you find the BSDL model of the CY37032P44 device? Answer: The BSDL model of the CY37032P44 device is attached: BSDL 32P44A.txt. Please be aware that the entire CPLD pro... Version: ** Question: How do you get the current Rx level (noise or data) from the powerline communication (PLC)? Answer: Band-in-use (BIU) must be enabled in all the devices for Rx noise measurement to... Version: ** Question: How do you use a 32 KHz external crystal oscillator with PLC20? Answer: Here are the settings needed to use an external 32 KHz crystal: In Global Resources, set 32K_Select... Question: 1)How can I use the HOTLink1 parts in a SMPTE-259M application?2)Does Cypress have a part that supports the SMPTE 310M video standard? Answer: Within the HOTLink1 family of parts there was a SM... Question: What information do you have about rad hardness, Soft Error Rate (SER), Single Event Upset (SEU) rates for the CY7B923 and CY7B933? Answer: Cypress doesn't have any measurement data on radhard-ness ... Question: - How do I connect the differential PECL outputs of the CY7C924ADX or CY7C9689A to a single-ended LVTTL input?- Is it possible to use a LVTTL optical module?- How do I make a PECL to LVTTL translation? ... Question: Is PAL22V10B a valid Cypress device? Answer: The PAL22V10B is not a CY part number. The equivalent CY part number for PAL22V10B is PALC22V10-xx. Please note all our CPLD/PLD families of de... Question: I have not been able to install USBisr on Windows XP x64. Is there a different driver for 64-bit XP? Answer: No, the ISR 4.0.1 programming software does not have the Driver support for the win... Question: What is the difference between SVF and STAPL file formats and how should one select between the two? Answer: User can select file format SVF or STAPL depending on their requirment. The Serial ... Question: What is the design software that supports CY7C343 devices? Answer: The part CY7C343 belong to MAX340 Family of devices. It was supported in Warp Software. We have stopped distributing Warp because o... Question: How was CY7C374U device programmed.How is it different from CY7C374i Answer: The CY7C374U device is programmed through some of its I/O pins. The CY7C374i is programmed through its JTAG interface and...
Get a feed of this content