• Why does AN64846 state SmartSense Auto-Tuning does NOT exist for Fourth Generation Capsense?

    Ap Note AN64846 implies there is no Auto Tuning with Fourth Generation Capsense. Is that correct?   Reference: Table 4-3 PSoC 4 Family Features Comparison in AN64846 - Getting Started with CapSense - Rev X on Pa...
    GrCa_1363456
    last modified by GrCa_1363456
  • where can I download the driver program of CY8CKIT-042

    I have a cy8ckit-042,but when link it to my computer,Inside the computer device manager, always show the driver is not correct As shown in the following figure. What's the correct driver program?   I have do...
    leka_3804381
    last modified by leka_3804381
  • PSOC4(CY8C4014SXI-421)

    4014内部是否有随机数生成器?如果有的话请介绍说明一下,代码位置,或组件设置等。谢谢。
    qime_3244791
    last modified by qime_3244791
  • Capsence layoute Designing

    Hello, I'm Vaibhav Italiya From India , currently I Start My New Business In Home Automation Sector With Capsence Touch Board For Wall Switch On IOT Application , Currently i Learning with PCB Layout Designing , I ha...
    Vait_4122196
    last modified by Vait_4122196
  • The ADC component can not work stand along in PSOC 4700S

    Hello,   I work on CY8CKIT-148 and just want to simply use a 10bit ADC component stand along, but it halts the line while(ADC_IsBusy() != ADC_STATUS_IDLE) within ADC_Start() . I guess the MagSense function is ...
    chwa_1570756
    last modified by chwa_1570756
  • CapSense baseline noise problem.

    Hi all     Customer project encountered a problem.Choosing sync when adjusting baseline is different from choosing noise interference. Phenomenon is like graph.    This is choose sync'd rea...
    yach_4179311
    last modified by yach_4179311
  • Special ports of GPIO

    Hello,   I consider designing with PSoC4100SPlus and refer to the following application note. But there is no description about the device. - PSoC 4 Hardware Design Considerations (AN88619)   Especially, ...
    KaKo_4074056
    last modified by KaKo_4074056
  • Re: UART Communication block

    what I am trying to do is pass different period values (2 bytes) to counter 1, 2, and 3 through the hyper terminal (have them saved in a memory or buffer) then after I do a an external reset my outputs from the TCPWM ...
    misa_4395186
    last modified by misa_4395186
  • Can UART of PSOC4 work at the baudrate of 2.5Mbps?

    Hello,   I need a 2.5Mbps baudrate of UART and set it with the code below:   UART_Stop(); clk_divide = 40000000/2500000/8-1;     //the oversampling of 8 has been set in UART component ...
    chwa_1570756
    last modified by chwa_1570756
  • What sort of runaway causes a reset on PSoC4000S?

    Hello,   We know that there is the explanation about Watch Dog Timer in "Watchdog Timer in the PSoC® 4000 Family – KBA91373". Of course, in case of PSoC4000S, there is a difference in the number of W...
    YoIs_1298666
    last modified by YoIs_1298666
  • EmEEPROM shared by both Bootloader and Application

    Hello,   I'm using PSoC4100S family micro-controller (CY8C4146LQI-S422T). I'm trying to share EmEEPROM between Bootloader and Application. I would want both Bootloader and application to be able to read/write th...
    PrSo_4458906
    last modified by PrSo_4458906
  • Regarding how to confirm PSoC4(CY8C4125) reset trigger.

    Hello.   Customer would like to confirm reset trigger. They would like to distinguish which reset occurred.   Is there way to confirm which reset trigger of Power On Reset, Brown out Reset and External ...
    YuMa_1534086
    last modified by YuMa_1534086
  • Solution: Use Kitprog to Program PSoC 4000 without XRES pin

    Solution: Use Kitprog to Program PSoC 4000 without XRES pin   version 1 Sept 12, 2019.   Several PSoC 4000 chips do not have the XRES pin.  XRES is typically used by Kitprog to reset the chip to acqu...
    BiBi_1928986
    created by BiBi_1928986
  • How to create callback from bootloader on PSoC 4?

    This code in the bootloader seems to make defining a callback macro for new commands for the bootloader difficult:   #if ((CYDEV_PROJ_TYPE != CYDEV_PROJ_TYPE_LAUNCHER) && (!CY_PSOC3)) /** *  This...
    JoWi_3984961
    last modified by JoWi_3984961
  • Ezi2c Write callback

    Hi,      客户在使用EZI2C的时候,希望在I2C Master完成写入操作后,通过EZI2C callback的方式进行数据处理,但是没有找到相关的API,请问,有EZI2C的callback处理的相关例程么?   Best Regards Simon
    SiCh_2873226
    last modified by SiCh_2873226
  • Can I read a program from Psoc4?

    I need to know the version of the program that was previously designed with CY8C4127LTI-M475. However, I don't know how to read program data for PIC. Please let me know if you have any reading methods or tools.
    kaka_3633091
    last modified by kaka_3633091
  • CySmart 4.2 access

    I need to send some data to a PSOC device via Cypress BLE dongle (CY SAMRT 4.2) This through a dedicated GUI I am building. I am looking for a library I can use to access the dongle via the USB port. Any documenta...
    D.Sd_3235936
    last modified by D.Sd_3235936
  • cy8ckit-046 PSOC 4L USB Audio streaming

    Using Windows 10 Using the USB Audio example on the mentioned cy8ckit-046.   The device enumerates but does not stream audio out the audio jack.   No changes to the example were made.     Keith
    keva_4443946
    last modified by keva_4443946
  • UART Communication block

    I am trying to use the UART communication block using CY8CKIT-043 prototype kit. I am using the standard UART block with the default settings. I only have two commands, UART_Start(); and UART_UART_PutString ("Hello Wo...
    misa_4395186
    last modified by misa_4395186
  • PSoc 4000, 4200, FLASH programming current consumption?

    Datasheets for PSoC 4000 CY8C4013SXI-410 and PSoC 4200 CY8C4245AXI-483, do not list DC current consumption for programming/erasing/writing FLASH.   For VDD of +5V, 16MHz for 4000 and 48MHz for 4200, 25C temperat...
    BiBi_1928986
    last modified by BiBi_1928986